老哥,这板子的硬编码弄出来了吗,必须得是camdroid才能用吗
不用的,linux也支持硬件h264编解码。我的贴子有效果。
]]>这几天使用华嵌的S3核心板尝试跑Rainbow-Pi的sdk,但是烧录不上(打包出img来后用tf卡烧录的方式),这个板子是用的emmc,用Rainbow-Pi的sdk没有在上面跑起来,然后把华嵌的S3核心板上emmc替换成MX35LF1GE4AB,也是烧录不上。
然后又尝试去搞一下tina,看到里面有一个r11跟s3 、v3s差不多,都是f35吧,试了一下也是烧录不上。
有哪位大侠用过s3跑官方sdk的么。
下面是华嵌的S3核心板上emmc替换成MX35LF1GE4AB,使用tf卡烧录时的log:
HELLO! BOOT0 is starting!
boot0 version : 4.0.0
boot0 commit : 5bde7999aad829824ac6b80a49dad0a502609447
fel flag = 0x00000000
rtc[0] value = 0x00000000
rtc[1] value = 0x00000000
rtc[2] value = 0x00000000
rtc[3] value = 0x00000000
rtc[4] value = 0x00000000
rtc[5] value = 0x00000000
rtc[6] value = 0x00000000
rtc[7] value = 0x00000000
DRAM DRIVE INFO: V0.7
DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 408 MHz
DRAM zq value: 000039bb
DRAM size = 128 MB
dram size =128
card boot number = 0
card no is 0
sdcard 0 line count 4
[mmc]: mmc driver ver 2014-12-10 21:20:39
[mmc]: ***Try SD card 0***
[mmc]: SD/MMC Card: 4bit, capacity: 3840MB
[mmc]: vendor: Man 00000000 Snr 12800003
[mmc]: product: APPSD
[mmc]: revision: 0.0
[mmc]: ***SD/MMC 0 init OK!!!***
sdcard 0 init ok
The size of uboot is 000ac000.
sum=aa12155c
src_sum=aa12155c
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
[ 0.306]
U-Boot 2011.09-rc1-00000-g5bde799-dirty (Jun 18 2020 - 09:44:02) Allwinner Technology
[ 0.315]version: 1.1.0
[ 0.318]uboot commit : 5bde7999aad829824ac6b80a49dad0a502609447
[ 0.328]pmbus: ready
not set main pmu id
axp_probe error
[ 0.334]PMU: pll1 408 Mhz,PLL6=600 Mhz
AXI=204 Mhz,AHB=204 Mhz, APB1=102 Mhz
set power on vol to default
dcdc2_vol = 1200
axp set dcdc2_vol to 1200 failed
dcdc3_vol = 3300
axp set dcdc3_vol to 3300 failed
aldo2_vol = 2500
axp set aldo2_vol to 2500 failed
aldo3_vol = 3000
axp set aldo3_vol to 3000 failed
ldo1_vol = 3300
axp set ldo1_vol to 3300 failed
ldo2_vol = 3000
axp set ldo2_vol to 3000 failed
ldo3_vol = 2800
axp set ldo3_vol to 2800 failed
ldo4_vol = 1800
axp set ldo4_vol to 1800 failed
find power_sply to end
vbus exist
no battery, limit to dc
dram_para_set start
dram_para_set end
[ 0.468]DRAM: 128 MiB
relocation Offset is: 0709c000
save config for small mem_size
Not Found clk pll_de in script
Not Found clk pll_video1 in script
Not Found clk pll_video in script
Not Found clk pll_periph0 in script
DRV_DISP_Init end
[ 0.576]fetch script data boot_disp.output_disp fail
[ 0.581]fetch script data boot_disp.output_type fail
[ 0.586]fetch script data boot_disp.output_mode fail
[ 0.591]fetch script data boot_disp.auto_hpd fail
[ 0.596]lcd0_para.lcd_used=0
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
disp0 device type(0) enable
workmode = 17
storage type = 1
NAND_UbootProbe start
NB1 : enter phy init
NandHwInit: Start Nand Hardware initializing .....
uboot:nand version: 2 25 20150917 1145
Reg 0x01c20848: 0x3333
Reg 0x01c2085c: 0x55
Reg 0x01c20864: 0x10
uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x47a319b0
request general tx dma channel ok!
uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x47a319cc
request general rx dma channel ok!
SPI nand ID: 0 0
_SearchNandArchi fail
[ERR]NandHwInit: SCN_AnalyzeNandSystem() failed!
NandHwInit: End Nand Hardware initializing ..... FAIL!
NB1 : nand phy init fail
NB1 : enter phy Exit
nand release dma:47a319b0
nand release dma:0
NAND_UbootProbe end: 0xffffffff
try nand fail
[ 0.674][mmc]: mmc driver ver 2015-04-13 14:50:00
err: gpio count < =0 ,gpio_count is: 0
[ 0.683][mmc]: get sdc_phy_wipe fail.
[ 0.686][mmc]: get sdc0 sdc_erase fail.
[ 0.690][mmc]: get sdc_2xmode fail used = 0
[ 0.695][mmc]: get sdc_ddrmode fail used = 0
[ 0.700][mmc]: get sdc_f_max fail,use default 50000000Hz
[ 0.705][mmc]: get card_line fail,use default card_line 4
[ 0.711][mmc]: get sdc_ex_dly_used fail,use default
[ 0.716][mmc]: SUNXI SD/MMC: 2
[ 2.718][mmc]: mmc 2,update clk failed
[ 2.721][mmc]: [mmc]: mmc 2 update clock failed
[ 2.727][mmc]: mmc 2 Found fatal err,so no send cmd
[ 2.732][mmc]: go idle failed
[ 2.735][mmc]: mmc go idle error
[ 2.738][mmc]: erase_grp_size:0x0WrBlk * 0x0 = 0x0 Byte
[ 2.744][mmc]: secure_feature 0x0
[ 2.747][mmc]: secure_removal_type 0x0
MMC init failed
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
mbr not exist
Net: eth0Warning: failed to set MAC address
[ 2.765]Hit any key to stop autoboot: 0
work mode=0x11
run card sprite
try sprite_led_gpio config
[ 2.775]sunxi sprite begin
sunxi sprite error: unable to get firmware start position
sunxi sprite firmware probe fail
sunxi#
问了一下店家,已经没有板子了。应该是拆机的散件。
感谢楼主分享,期待更新, 并求行车记录仪购买链接.
问了一下店家,已经没有板子了。应该是拆机的散件。
]]>