[157]HELLO! BOOT0 is starting! [160]BOOT0 commit : 5224261 [162]set pll start [164]fix vccio detect value:0xc0 [171]periph0 has been enabled [175]set pll end [176][pmu]: bus read error [179]board init ok [181]enable_jtag [182]ZQ value = 0x2f [184]get_pmu_exist() = -1 [187]DRAM BOOT DRIVE INFO: V0.32 [190]DRAM CLK = 792 MHz [192]DRAM Type = 3 (2:DDR2,3:DDR3) [196]DRAMC read ODT off. [198]DRAM ODT value: 0x42. [201]ddr_efuse_type: 0xa [203]mark_id: 0x60 [206]DRAM SIZE =128 M [208]PLL_DDR_CTRL_REG:0xf8004100 [211]DRAM_CLK_REG:0xc0000000 [214][TIMING DEBUG] MR2= 0x18 [221]DRAM simple test OK. [223]rtc standby flag is 0x0, super standby flag is 0x0 [229]dram size =128 [231]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32 [237]block from 8 to 32 [346]Check is correct. [348]dma 0x29c4c int is not used yet [352]dma 0x29c4c int is free, you do not need to free it again [357]Entry_name = u-boot [365]Entry_name = optee [369]Entry_name = dtb [372]Jump to second Boot. M/TC: OP-TEE version: 53fe17e2-dirty (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #6 Fri Feb 18 08:54:51 UTC 2022 arm U-Boot 2018.05 (Oct 25 2024 - 11:14:54 +0800) Allwinner Technology [00.428]CPU: Allwinner Family [00.431]Model: sun8iw20 [00.433]DRAM: 128 MiB [00.437]Relocation Offset is: 04ec6000 [00.464]secure enable bit: 0 [00.466]smc_tee_inform_fdt failed with: -65526[00.470]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.476]gic: sec monitor mode [00.479]flash init start [00.481]workmode = 0,storage type = 0 sspi->base_addr = 0x4025000, the SPI control register: [VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184 [ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020 [FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002 [SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000 [BCC] 0x4025038 = 0x10000000, [DMA] 0x4025088 = 0x000000e5 [00.528]sunxi-spinand-phy: not detect any munufacture from id table [00.535]sunxi-spinand-phy: get spi-nand Model from fdt fail [00.540]sunxi-spinand-phy: get phy info from fdt fail device nand0 , # parts = 4 #: name size offset mask_flags 0: boot0 0x00100000 0x00000000 1 1: uboot 0x00300000 0x00100000 1 2: secure_storage 0x00100000 0x00400000 1 3: sys 0x07b00000 0x00500000 0 active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000 defaults: mtdids : nand0=nand mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) [00.724]ubi0: attaching mtd4 [01.011]ubi0: scanning is finished [01.021]ubi0: attached mtd4 (name "sys", size 123 MiB) [01.026]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes [01.032]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048 [01.039]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [01.045]ubi0: good PEBs: 488, bad PEBs: 4, corrupted PEBs: 0 [01.050]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128 [01.057]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0 [01.065]ubi0: available PEBs: 0, total reserved PEBs: 488, PEBs reserved for bad PEB handling: 16 [01.073]sunxi flash init ok [01.076]line:703 init_clocks [01.079]drv_disp_init request pwm success, pwm7:pwm7:0x2000c00. [01.093]drv_disp_init finish [01.096]boot_gui_init:start [01.099]set disp.dev2_output_type fail. using defval=0 [01.105]boot_gui_init:finish [01.285]LCD open finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [01.436]bmp_name=bootlogo.bmp size 1152054 1152054 bytes read in 166 ms (6.6 MiB/s) [01.906]Loading Environment from SUNXI_FLASH... OK [01.953]Item0 (Map) magic is bad secure storage read widevine fail [01.959]secure storage read widevine fail with:-1 secure storage read ec_key fail [01.966]secure storage read ec_key fail with:-1 secure storage read ec_cert1 fail [01.974]secure storage read ec_cert1 fail with:-1 secure storage read ec_cert2 fail [01.981]secure storage read ec_cert2 fail with:-1 secure storage read ec_cert3 fail [01.988]secure storage read ec_cert3 fail with:-1 secure storage read rsa_key fail [01.996]secure storage read rsa_key fail with:-1 secure storage read rsa_cert1 fail [02.003]secure storage read rsa_cert1 fail with:-1 secure storage read rsa_cert2 fail [02.011]secure storage read rsa_cert2 fail with:-1 secure storage read rsa_cert3 fail [02.019]secure storage read rsa_cert3 fail with:-1 [02.023]usb burn from boot delay time 0 weak:otg_phy_config [02.034]usb prepare ok [02.837]overtime [02.840]do_burn_from_boot usb : no usb exist List file under ULI/factory ** Unrecognized filesystem type ** [02.879]update bootcmd [02.910]change working_fdt 0x44885e70 to 0x44865e70 [02.927]update dts Hit any key to stop autoboot: 0 [10.305]no vendor_boot partition is found Android's image name: sun8i_arm [10.324]Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.61 (zx@ubuntu) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #13 SMP PREEMPT Fri Oct 25 11:16:12 CST 2024 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructi on cache [ 0.000000] OF: fdt: Machine model: sun8iw20 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 8 MiB at 0x47800000 [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 15 pages/cpu s30912 r8192 d22336 u61440 [ 0.000000] pcpu-alloc: s30912 r8192 d22336 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: ubi.mtd=sys earlycon=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=ubi0_3 rootfstype=ubifs,rw init=/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@u bi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:private@ubi0_7:UD ISK@ubi0_8: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidb oot.hardware=sun8iw20p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message =2018.05(10/25/2024-11:14:54) disp_reserve=2457600,0x44909000 aw-ubi-spinand.ub ootblks=24 androidboot.dramsize=128 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, l inear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, lin ear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 99840K/131072K available (6144K kernel code, 405K rwdata , 2148K rodata, 1024K init, 168K bss, 23040K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 ji ffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x24c/0x42c wi th crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles : 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398 046511097ns [ 0.000018] Switching to timer-based delay loop, resolution 41ns [ 0.000353] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max _idle_ns: 79635851949 ns [ 0.001048] Console: colour dummy device 80x30 [ 0.001094] Calibrating delay loop (skipped), value calculated using timer f requency.. 48.00 BogoMIPS (lpj=240000) [ 0.001108] pid_max: default: 32768 minimum: 301 [ 0.001923] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, line ar) [ 0.001938] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.005082] CPU: Testing write buffer coherency: ok [ 0.006335] /cpus/cpu@0 missing clock-frequency property [ 0.006361] /cpus/cpu@1 missing clock-frequency property [ 0.006373] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.008130] Setting up static identity map for 0x40100000 - 0x40100060 [ 0.008447] rcu: Hierarchical SRCU implementation. [ 0.009617] smp: Bringing up secondary CPUs ... [ 0.011886] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012052] smp: Brought up 1 node, 2 CPUs [ 0.012069] SMP: Total of 2 processors activated (96.00 BogoMIPS). [ 0.012076] CPU: All CPU(s) started in SVC mode. [ 0.014448] devtmpfs: initialized [ 0.178362] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.180514] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, m ax_idle_ns: 19112604462750000 ns [ 0.180546] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.181083] pinctrl core: initialized pinctrl subsystem [ 0.188566] NET: Registered protocol family 16 [ 0.191322] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.362603] rtc_ccu: sunxi ccu init OK [ 0.376100] ccu: sunxi ccu init OK [ 0.377968] r_ccu: sunxi ccu init OK [ 0.596708] iommu: Default domain type: Translated [ 0.597468] sunxi iommu: irq = 24 [ 0.607422] SCSI subsystem initialized [ 0.609623] usbcore: registered new interface driver usbfs [ 0.610148] usbcore: registered new interface driver hub [ 0.610907] usbcore: registered new device driver usb [ 0.624071] Bluetooth: Core ver 2.22 [ 0.624373] NET: Registered protocol family 31 [ 0.624384] Bluetooth: HCI device and connection manager initialized [ 0.624430] Bluetooth: HCI socket layer initialized [ 0.624463] Bluetooth: L2CAP socket layer initialized [ 0.624557] Bluetooth: SCO socket layer initialized [ 0.625698] pwm module init! [ 0.631635] input: sunxi-keyboard as /devices/virtual/input/input0 [ 0.636741] clocksource: Switched to clocksource arch_sys_counter [ 0.707610] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.795703] thermal_sys: Registered thermal governor 'step_wise' [ 0.795711] thermal_sys: Registered thermal governor 'user_space' [ 0.795727] thermal_sys: Registered thermal governor 'power_allocator' [ 0.799175] NET: Registered protocol family 2 [ 0.802490] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.802570] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.802619] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.802642] TCP: Hash tables configured (established 1024 bind 1024) [ 0.803085] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.803146] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.803917] NET: Registered protocol family 1 [ 0.809191] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator [ 0.811355] spi spi0: spi0 supply spi not found, using dummy regulator [ 0.812574] sunxi_spi_resource_get()2151 - [spi0] SPI MASTER MODE [ 0.812851] sunxi_spi_resource_get()2189 - Failed to get sample mode [ 0.812863] sunxi_spi_resource_get()2194 - Failed to get sample delay [ 0.812873] sunxi_spi_resource_get()2198 - sample_mode:-1431633921 sample_de lay:-1431633921 [ 0.812934] sunxi_spi_clk_init()2240 - [spi0] mclk 100000000 [ 0.816583] sunxi_spi_probe()2653 - [spi0]: driver probe succeed, base c8821 000, irq 41 [ 0.824804] Initialise system trusted keyrings [ 0.825240] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.910314] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.944024] NET: Registered protocol family 38 [ 0.944131] Key type asymmetric registered [ 0.944142] Asymmetric key parser 'x509' registered [ 0.944496] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.944509] io scheduler mq-deadline registered [ 0.944518] io scheduler kyber registered [ 0.944763] atomic64_test: passed [ 0.958217] [DISP]disp_module_init [ 0.960596] disp 5000000.disp: Adding to iommu group 0 [ 0.963241] [DISP] disp_init,line:2386: [ 0.963247] smooth display screen:0 type:1 mode:4 [ 0.982921] display_fb_request,fb_id:0 [ 0.992030] disp_al_manager_apply ouput_type:1 [ 0.992681] [DISP] lcd_clk_config,line:735: [ 0.992693] disp 0, clk: pll(364000000),clk(364000000),dclk(52000000) dsi_ra te(364000000) [ 0.992693] clk real:pll(360000000),clk(360000000),dclk(51428571) dsi_r ate(0) [ 0.993571] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator [ 0.994464] wait for new fb take effect [ 1.038353] Freeing logo buffer memory: 2400K [ 1.039904] [DISP]disp_module_init finish [ 1.042092] sunxi_sid_init()551 - insmod ok [ 1.045756] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.046527] uart uart3: get regulator failed [ 1.046551] uart uart3: uart3 supply uart not found, using dummy regulator [ 1.048186] uart3: ttyS0 at MMIO 0x2500c00 (irq = 34, base_baud = 1500000) i s a SUNXI [ 1.048220] sw_console_setup()1784 - console setup baud 115200 parity n bits 8, flow n [ 1.954533] printk: console [ttyS0] enabled [ 1.963313] misc dump reg init [ 1.972655] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 1.980151] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 1.987673] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 1.995136] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 2.001696] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 2.008690] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1) [ 2.016595] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=131 assert=1 [ 2.024628] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 2.036331] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert =1 [ 2.044542] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 2.053068] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 2.059911] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1) [ 2.067678] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0 [ 2.083242] sunxi-spinand: AW SPINand MTD Layer Version: 2.0 20201228 [ 2.090583] sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.10 20200306 [ 2.098701] sunxi-spinand-phy: not detect any munufacture from id table [ 2.106128] sunxi-spinand-phy: get spi-nand Model from fdt fail [ 2.112796] sunxi-spinand-phy: get phy info from fdt fail [ 2.118922] sunxi-spinand-phy: not detect munufacture from fdt [ 2.125707] sunxi-spinand-phy: detect munufacture from id table: XTX [ 2.132864] sunxi-spinand-phy: detect spinand id: ffff110b ffffffff [ 2.139923] sunxi-spinand-phy: ========== arch info ========== [ 2.146467] sunxi-spinand-phy: Model: XT26G01C [ 2.152828] sunxi-spinand-phy: Munufacture: XTX [ 2.158698] sunxi-spinand-phy: DieCntPerChip: 1 [ 2.164360] sunxi-spinand-phy: BlkCntPerDie: 1024 [ 2.170326] sunxi-spinand-phy: PageCntPerBlk: 64 [ 2.176086] sunxi-spinand-phy: SectCntPerPage: 4 [ 2.181760] sunxi-spinand-phy: OobSizePerPage: 64 [ 2.187531] sunxi-spinand-phy: BadBlockFlag: 0x0 [ 2.193388] sunxi-spinand-phy: OperationOpt: 0x7 [ 2.199256] sunxi-spinand-phy: MaxEraseTimes: 50000 [ 2.205309] sunxi-spinand-phy: EccFlag: 0x0 [ 2.211177] sunxi-spinand-phy: EccType: 8 [ 2.216850] sunxi-spinand-phy: EccProtectedType: 1 [ 2.222512] sunxi-spinand-phy: ======================================== [ 2.229938] sunxi-spinand-phy: [ 2.233457] sunxi-spinand-phy: ========== physical info ========== [ 2.240403] sunxi-spinand-phy: TotalSize: 128 M [ 2.245774] sunxi-spinand-phy: SectorSize: 512 B [ 2.251159] sunxi-spinand-phy: PageSize: 2 K [ 2.256335] sunxi-spinand-phy: BlockSize: 128 K [ 2.261724] sunxi-spinand-phy: OOBSize: 64 B [ 2.267011] sunxi-spinand-phy: ======================================== [ 2.274428] sunxi-spinand-phy: [ 2.277957] sunxi-spinand-phy: ========== logical info ========== [ 2.284789] sunxi-spinand-phy: TotalSize: 128 M [ 2.290170] sunxi-spinand-phy: SectorSize: 512 B [ 2.295540] sunxi-spinand-phy: PageSize: 4 K [ 2.300726] sunxi-spinand-phy: BlockSize: 256 K [ 2.306096] sunxi-spinand-phy: OOBSize: 128 B [ 2.311476] sunxi-spinand-phy: ======================================== [ 2.319077] sunxi-spinand-phy: block lock register: 0x00 [ 2.325247] sunxi-spinand-phy: feature register: 0x11 [ 2.331039] sunxi-spinand-phy: sunxi physic nand init end [ 2.341428] sunxipart: failed to parse sunxi_gpt! [ 2.346755] Creating 4 MTD partitions on "sunxi_mtd_nand": [ 2.352976] 0x000000000000-0x000000100000 : "boot0" [ 2.364478] 0x000000100000-0x000000400000 : "uboot" [ 2.371474] random: fast init done [ 2.385195] 0x000000400000-0x000000500000 : "secure_storage" [ 2.397788] 0x000000500000-0x000008000000 : "sys" [ 2.465305] sunxi-spinand-phy: phy blk 245 is bad [ 2.528048] sunxi-spinand-phy: phy blk 440 is bad [ 2.589057] sunxi-spinand-phy: phy blk 635 is bad [ 2.648875] sunxi-spinand-phy: phy blk 830 is bad [ 2.714488] libphy: Fixed MDIO Bus: probed [ 2.722205] sun8iw20-pinctrl 2000000.pinctrl: pin PE3 already requested by 2 000000.pinctrl:131; cannot claim for 4500000.eth [ 2.734870] sun8iw20-pinctrl 2000000.pinctrl: pin-131 (4500000.eth) status - 22 [ 2.743002] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 131 (PE3 ) from group PE3 on device 2000000.pinctrl [ 2.755130] sunxi-gmac 4500000.eth: Error applying setting, reverse things b ack [ 2.765171] sunxi-gmac: probe of 4500000.eth failed with error -22 [ 2.772539] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.779895] sunxi-ehci: EHCI SUNXI driver [ 2.785045] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.792104] sunxi-ohci: OHCI SUNXI driver [ 2.798129] usbcore: registered new interface driver uas [ 2.804598] usbcore: registered new interface driver usb-storage [ 2.811848] usbcore: registered new interface driver ums-alauda [ 2.818834] usbcore: registered new interface driver ums-cypress [ 2.825867] usbcore: registered new interface driver ums-datafab [ 2.832939] usbcore: registered new interface driver ums_eneub6250 [ 2.840183] usbcore: registered new interface driver ums-freecom [ 2.847269] usbcore: registered new interface driver ums-isd200 [ 2.854179] usbcore: registered new interface driver ums-jumpshot [ 2.861331] usbcore: registered new interface driver ums-karma [ 2.868204] usbcore: registered new interface driver ums-onetouch [ 2.875462] usbcore: registered new interface driver ums-realtek [ 2.882543] usbcore: registered new interface driver ums-sddr09 [ 2.889484] usbcore: registered new interface driver ums-sddr55 [ 2.896389] usbcore: registered new interface driver ums-usbat [ 2.906031] ts probe start [ 2.908451] input: 2009c00.rtp as /devices/platform/soc@3000000/2009c00.rtp/ input/input1 [ 2.921834] ts probe success [ 2.923477] sunxi_gpadc_init,2137, success [ 2.933074] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value() : ALARM0_DAY_REG=0, set it to 1 [ 2.949537] sunxi-rtc 7090000.rtc: registered as rtc0 [ 2.955339] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00: 12 UTC (12) [ 2.964511] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 2.970822] i2c /dev entries driver [ 2.975058] IR NEC protocol handler initialized [ 2.980219] IR RC5(x/sz) protocol handler initialized [ 2.986767] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 2.998802] sunxi_ir_startup: get ir protocol failed [ 2.998822] (NULL device *): deviceless supply not found, using dummy regul ator [ 3.013176] Registered IR keymap rc_map_sunxi [ 3.019015] rc rc0: sunxi-ir as /devices/platform/soc@3000000/7040000.s_cir/ rc/rc0 [ 3.028827] input: sunxi-ir as /devices/platform/soc@3000000/7040000.s_cir/r c/rc0/s_cir_rx [ 3.040907] sunxi cedar version 1.1 [ 3.045477] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 3.051910] VE: sunxi_cedar_probe power-domain init!!! [ 3.057708] VE: install start!!! [ 3.057708] [ 3.064399] VE: cedar-ve the get irq is 42 [ 3.064399] [ 3.071719] VE: ve_debug_proc_info:(ptrval), data:(ptrval), lock:(ptrval) [ 3.071719] [ 3.081055] VE: install end!!! [ 3.081055] [ 3.086136] VE: sunxi_cedar_probe [ 3.093941] sunxi-wdt 20500a0.watchdog: Watchdog enabled (timeout=16 sec, no wayout=0) [ 3.113636] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.2 1 2021-05-24 16:10) [ 3.123817] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 3.130102] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 3.136474] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 3.142951] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 3.149430] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 3.155975] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 3.162532] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 3.169099] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 3.177509] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 3.184441] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.195651] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 3.215848] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vd d 21 width 1 timing LEGACY(SDR12) dt B [ 3.240175] sunxi-mmc 4020000.sdmmc: detmode:gpio polling [ 3.246262] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 3.249656] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.2 1 2021-05-24 16:10) [ 3.267583] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 3.273797] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 3.280188] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 3.286635] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 3.293105] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 3.299665] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 3.306208] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 3.312765] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 3.319590] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check i f needed [ 3.331525] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 3.342744] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 3.362959] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vd d 21 width 1 timing LEGACY(SDR12) dt B [ 3.387291] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 3.394972] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.397755] usbcore: registered new interface driver usbhid [ 3.408127] usbhid: USB HID core driver [ 3.408935] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 3.412432] exFAT: Version 1.3.0 [ 3.422914] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vd d 21 width 1 timing LEGACY(SDR12) dt B [ 3.433122] rtk_btusb: Realtek Bluetooth USB driver ver 3.1.981c756.20211102 -175222 [ 3.443859] rtk_btcoex: rtk_btcoex_init: version: 1.2 [ 3.444446] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vd d 21 width 1 timing LEGACY(SDR12) dt B [ 3.449572] rtk_btcoex: create workqueue [ 3.465595] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.472382] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.479151] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.485905] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 3.485934] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 3.493029] rtk_btcoex: alloc buffers 1408, 2240 for ev and l2 [ 3.510983] usbcore: registered new interface driver rtk_btusb [ 3.525592] NET: Registered protocol family 10 [ 3.537777] Segment Routing with IPv6 [ 3.542199] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.558897] NET: Registered protocol family 17 [ 3.563994] NET: Registered protocol family 15 [ 3.569892] Registering SWP/SWPB emulation handler [ 3.577591] Loading compiled-in X.509 certificates [ 3.589833] HDMI 2.0 driver init start! [ 3.594209] boot_hdmi=false [ 3.597505] ERROR: can not get hdmi_cts_compatibility [ 3.603272] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 3.612051] HDMI2.0 module init end [ 3.732492] sun8iw20-pinctrl 2000000.pinctrl: pin PE3 already requested by 2 000000.pinctrl:131; cannot claim for 4500000.eth [ 3.745165] sun8iw20-pinctrl 2000000.pinctrl: pin-131 (4500000.eth) status - 22 [ 3.753310] sun8iw20-pinctrl 2000000.pinctrl: could not request pin 131 (PE3 ) from group PE3 on device 2000000.pinctrl [ 3.765437] sunxi-gmac 4500000.eth: Error applying setting, reverse things b ack [ 3.775499] sunxi-gmac: probe of 4500000.eth failed with error -22 [ 3.784370] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dum my regulator [ 3.798216] sunxi-i2c sunxi-i2c2: probe success [ 3.813522] get ehci0-controller wakeup-source is fail. [ 3.819873] sunxi ehci0-controller don't init wakeup source [ 3.826135] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunx i_ehci: 0xc0b86b90, 0x:c887e000, irq_no:38 [ 3.838181] [sunxi-ehci0]: Not init ehci0 [ 3.843513] get ohci0-controller wakeup-source is fail. [ 3.849882] sunxi ohci0-controller don't init wakeup source [ 3.856140] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunx i_ohci: 0xc0b86e20 [ 3.865838] [sunxi-ohci0]: Not init ohci0 [ 3.871200] get ehci1-controller wakeup-source is fail. [ 3.877484] sunxi ehci1-controller don't init wakeup source [ 3.883769] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunx i_ehci: 0xc0b870b0, 0x:c9511000, irq_no:3a [ 3.897229] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller su pply hci not found, using dummy regulator [ 3.911880] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 3.919370] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, ass igned bus number 1 [ 3.930038] sunxi-ehci 4200000.ehci1-controller: irq 58, io mem 0x04200000 [ 3.966763] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 3.980469] hub 1-0:1.0: USB hub found [ 3.984985] hub 1-0:1.0: 1 port detected [ 3.993567] get ohci1-controller wakeup-source is fail. [ 3.999973] sunxi ohci1-controller don't init wakeup source [ 4.006231] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunx i_ohci: 0xc0b87340 [ 4.017319] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller su pply hci not found, using dummy regulator [ 4.030820] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 4.038236] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, ass igned bus number 2 [ 4.048889] sunxi-ohci 4200400.ohci1-controller: irq 59, io mem 0x04200400 [ 4.126567] hub 2-0:1.0: USB hub found [ 4.131165] hub 2-0:1.0: 1 port detected [ 4.142288] ubi0: attaching mtd3 [ 4.429821] random: crng init done [ 4.660675] ubi0: scanning is finished [ 4.665045] ubi0 error: ubi_read_volume_table: the layout volume was not fou nd [ 4.681188] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd3, error -22 [ 4.689323] UBI error: cannot attach mtd3 [ 4.698073] ***CTP***GTP Driver Version: V2.2<2014/01/14> [ 4.698080] ***CTP***GTP I2C Address: 0x14 [ 4.704299] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 4.716875] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 4.724402] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 4.732330] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 4.739915] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 4.747841] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 4.755358] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 4.763286] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 4.770836] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 4.778763] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 4.786187] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 4.946750] <<-GTP-ERROR->> GTP i2c test failed time 1. [ 4.976843] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 4.984771] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 4.992308] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.000236] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.007771] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.015695] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.023227] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.031155] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.038683] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.046606] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.054078] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.216748] <<-GTP-ERROR->> GTP i2c test failed time 2. [ 5.246841] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.254768] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.262303] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.270231] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.277766] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.285691] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.293222] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.301151] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.308679] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.316601] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.324050] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.486747] <<-GTP-ERROR->> GTP i2c test failed time 3. [ 5.516839] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.524764] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.532295] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.540224] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.547758] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.555682] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.563212] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.571141] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.578669] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.586591] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.594039] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 5.756747] <<-GTP-ERROR->> GTP i2c test failed time 4. [ 5.786844] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.794772] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.802312] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.810257] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.817795] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.825722] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.833260] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.841190] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.848771] sunxi-i2c sunxi-i2c2: drv-mode: Timeout when sending 9th SCL clk [ 5.856694] sunxi-i2c sunxi-i2c2: drv-mode: xfer failed (dev addr:0x14) [ 5.864143] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -22! Process reset. [ 6.026748] <<-GTP-ERROR->> GTP i2c test failed time 5. [ 6.056745] I2C communication ERROR! [ 6.056859] gt9xxnew_ts: probe of 2-0014 failed with error -1 [ 6.068762] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 6.083213] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 6.091265] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 6.100999] clk: Not disabling unused clocks [ 6.105834] alloc_fd: slot 0 not NULL! [ 6.110110] cfg80211: failed to load regulatory.db [ 6.117168] VFS: Cannot open root device "ubi0_3" or unknown-block(0,0): error -19 [ 6.125666] Please append a correct "root=" boot option; here are the available partitions: [ 6.135105] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 6.144382] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.61 #13 [ 6.151116] Hardware name: Generic DT based system [ 6.156507] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 6.165200] [] (show_stack) from [] (dump_stack+0x7c/0x98) [ 6.173310] [] (dump_stack) from [] (panic+0x104/0x3dc) [ 6.181127] [] (panic) from [] (mount_block_root+0x278/0x32c) [ 6.189525] [] (mount_block_root) from [] (prepare_namespace+0x84/0x184) [ 6.198998] [] (prepare_namespace) from [] (kernel_init+0x8/0x10c) [ 6.207885] [] (kernel_init) from [] (ret_from_fork+0x14/0x2c) [ 6.216377] Exception stack(0xc704dfb0 to 0xc704dff8) [ 6.222042] dfa0: 00000000 00000000 00000000 00000000 [ 6.231218] dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 6.240393] dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 6.247818] CPU1: stopping [ 6.250856] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.61 #13 [ 6.257590] Hardware name: Generic DT based system [ 6.262970] [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [ 6.271661] [] (show_stack) from [] (dump_stack+0x7c/0x98) [ 6.279767] [] (dump_stack) from [] (handle_IPI+0xc0/0x168) [ 6.287971] [] (handle_IPI) from [] (gic_handle_irq+0x70/0x78) [ 6.296466] [] (gic_handle_irq) from [] (__irq_svc+0x6c/0xa8) [ 6.304859] Exception stack(0xc7097f80 to 0xc7097fc8) [ 6.310527] 7f80: 0000c9b0 c76c8534 00000000 c0114d80 00000002 c7096000 c0b03de8 c0b03e24 [ 6.319704] 7fa0: 4000406a 410fc075 00000000 00000000 c0b708f0 c7097fd0 c0107fa0 c0107fa4 [ 6.328877] 7fc0: 60000113 ffffffff [ 6.332793] [] (__irq_svc) from [] (arch_cpu_idle+0x2c/0x38) [ 6.341095] [] (arch_cpu_idle) from [] (do_idle+0xb8/0x120) [ 6.349298] [] (do_idle) from [] (cpu_startup_entry+0x18/0x1c) [ 6.357793] [] (cpu_startup_entry) from [<40102c0c>] (0x40102c0c) [ 6.365617] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---