WhyCan Forum(哇酷开发者社区)

U-Boot 2011.09-rc1 (Oct 18 2019 - 23:10:17) Allwinner Technology 

[      0.334]version: 1.1.0
[      0.337]uboot commit : 8 
[      0.343]pmbus:   ready
not set main pmu id
axp read error
probe axp20x failed
axp152 read error
probe axp15 failed
axp_probe error
[      0.470]PMU: pll1 408 Mhz,PLL6=600 Mhz
AXI=204 Mhz,AHB=204 Mhz, APB1=102 Mhz 
set power on vol to default
dcdc2_vol = 1200
axp set dcdc2_vol to 1200 failed
dcdc3_vol = 3300
axp set dcdc3_vol to 3300 failed
aldo2_vol = 2500
axp set aldo2_vol to 2500 failed
aldo3_vol = 3000
axp set aldo3_vol to 3000 failed
ldo1_vol = 3300
axp set ldo1_vol to 3300 failed
ldo2_vol = 3000
axp set ldo2_vol to 3000 failed
ldo3_vol = 3000
axp set ldo3_vol to 3000 failed
find power_sply to end
vbus exist
no battery, limit to dc
dram_para_set start
dram_para_set end
[      0.600]DRAM:  64 MiB
relocation Offset is: 030a0000
save config for small mem_size 
Not Found clk pll_de in script 
Not Found clk pll_video1 in script 
Not Found clk pll_video in script 
Not Found clk pll_periph0 in script 
DRV_DISP_Init end
[      0.711]fetch script data boot_disp.output_disp fail
[      0.716]fetch script data boot_disp.output_type fail
[      0.721]fetch script data boot_disp.output_mode fail
[      0.726]fetch script data boot_disp.auto_hpd fail
[      0.731]lcd0_para.lcd_used=1
[disk_read_fs] no the partition
error: open disp_rsl.fex, maybe it is not exist
disp0 device type(1) enable
lcd_panel_fun[0].cfg_open_flow is NULL
lcd_panel_fun[0].cfg_panel_info is NULL
disp 0, clk: pll(360000000),clk(90000000),dclk(9000000) dsi_rate(360000000)
     clk real:pll(114000000),clk(0),dclk(0) dsi_rate(0)
lcd_panel_fun[0].cfg_open_flow is NULL
lcd_panel_fun[0].cfg_open_flow is NULL
workmode = 17
storage type = 1
NAND_UbootProbe start
NB1 : enter phy init
NandHwInit: Start Nand Hardware initializing .....
uboot:nand version: 2 25 20150917 1145 
Reg 0x01c20848: 0x3333
Reg 0x01c2085c: 0x55
Reg 0x01c20864: 0x10
uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x43a34210
request general tx dma channel ok!
uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x43a3422c
request general rx dma channel ok!
SPI nand ID: 21aaef 0
_SearchNandArchi fail
[ERR]NandHwInit: SCN_AnalyzeNandSystem() failed!
NandHwInit: End Nand Hardware initializing ..... FAIL!
NB1 : nand phy init fail
NB1 : enter phy Exit
nand release dma:43a34210
nand release dma:0
NAND_UbootProbe end: 0xffffffff
try nand fail
[      0.835][mmc]: mmc driver ver 2015-04-13 14:50:00
err: gpio count < =0 ,gpio_count is: 0 
[      0.844][mmc]: get sdc_phy_wipe fail.
[      0.847][mmc]: get sdc0 sdc_erase fail.
[      0.851][mmc]: get sdc_2xmode fail  used =  0
[      0.856][mmc]: get sdc_ddrmode fail  used =  0
[      0.861][mmc]: get sdc_f_max fail,use default  50000000Hz
[      0.866][mmc]: get card_line fail,use default card_line 4
[      0.872][mmc]: get sdc_ex_dly_used fail,use default
[      0.877][mmc]: SUNXI SD/MMC: 2
[      2.879][mmc]: mmc 2,update clk failed
[      2.882][mmc]: [mmc]: mmc 2  update clock failed
[      2.888][mmc]: mmc 2 Found fatal err,so no send cmd
[      2.893][mmc]: go idle failed
[      2.896][mmc]: mmc go idle error
[      2.899][mmc]: erase_grp_size:0x0WrBlk * 0x0 = 0x0 Byte
[      2.905][mmc]: secure_feature 0x0
[      2.908][mmc]: secure_removal_type  0x0
MMC init failed
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
mbr not exist
[      2.922]Hit any key to stop autoboot:  0 
work mode=0x11
run card sprite
try sprite_led_gpio config
[      2.932]sunxi sprite begin
sunxi sprite error: unable to get firmware start position
sunxi sprite firmware probe fail