楼主 #1 2019-04-16 14:26:52 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
把 Linux4.13 替换成 4.10, 系统提示 FATAL: kernel too old, 然后奔溃
奔溃现场:
[ 4.556319] VFS: Mounted root (jffs2 filesystem) on device 31:4.
[ 4.563812] devtmpfs: mounted
[ 4.567967] Freeing unused kernel memory: 1024K
FATAL: kernel too old
[ 4.768232] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[ 4.768232]
[ 4.777374] CPU: 0 PID: 1 Comm: linuxrc Not tainted 4.10.15-licheepi-zero-00962-g02a01d8 #18
[ 4.785797] Hardware name: Allwinner sun8i Family
[ 4.790537] [<c010e494>] (unwind_backtrace) from [<c010b230>] (show_stack+0x10/0x14)
[ 4.798281] [<c010b230>] (show_stack) from [<c0358368>] (dump_stack+0x84/0x98)
[ 4.805503] [<c0358368>] (dump_stack) from [<c01a7b84>] (panic+0xdc/0x248)
[ 4.812378] [<c01a7b84>] (panic) from [<c011e358>] (do_exit+0x9d0/0xa00)
[ 4.819074] [<c011e358>] (do_exit) from [<c011f4c4>] (do_group_exit+0x3c/0xd0)
[ 4.826290] [<c011f4c4>] (do_group_exit) from [<c011f568>] (__wake_up_parent+0x0/0x18)
[ 4.834204] Rebooting in 5 seconds..
全部 log:
U-Boot SPL 2017.01-rc2-00074-g3214598-dirty (Apr 10 2019 - 21:26:39)
DRAM: 64 MiB
Trying to boot from sunxi SPI
U-Boot 2017.01-rc2-00074-g3214598-dirty (Apr 10 2019 - 21:26:39 -0400) Allwinner Technology
CPU: Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
*** Warning - bad CRC, using default environment
Setting up a 1024x600 lcd console (overscan 0x0)
dotclock: 48000kHz = 48000kHz: (1 * 3MHz * 96) / 6
In: serial@01c28800
Out: serial@01c28800
Err: serial@01c28800
U-Boot 2017.01-rc2-00074-g3214598-dirty (Apr 10 2019 - 21:26:39 -0400) Allwinner Technology
CPU: Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
*** Warning - bad CRC, using default environment
Setting up a 1024x600 lcd console (overscan 0x0)
dotclock: 48000kHz = 48000kHz: (1 * 3MHz * 96) / 6
In: serial@01c28800
Out: serial@01c28800
Err: serial@01c28800
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0x100000, size 0x4000
SF: 16384 bytes @ 0x100000 Read: OK
device 0 offset 0x110000, size 0x500000
SF: 5242880 bytes @ 0x110000 Read: OK
## Flattened Device Tree blob at 41800000
Booting using the fdt blob at 0x41800000
Loading Device Tree to 42df9000, end 42dff04f ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.10.15-licheepi-zero-00962-g02a01d8 (root@test4) (gcc version 5.4.0 20160609 (Ubuntu/Linaro 5.4.0-6ubuntu1~16.04.9) ) #18 SMP Mon Apr 15 21:11:46 EDT 2019
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: Lichee Pi Zero with Dock
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 14 pages/cpu @c3d08000 s24780 r8192 d24372 u57344
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15660
[ 0.000000] Kernel command line: console=ttyS2,115200 earlyprintk panic=5 rootwait mtdparts=spi32766.0:992k(uboot)ro,32k(env)ro,64k(dtb)ro,5M(kernel)ro,-(rootfs) root=31:04 rw rootfstype=jffs2 init=/linuxrc vt.global_cursor_default=0
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 51584K/63136K available (6144K kernel code, 310K rwdata, 2084K rodata, 1024K init, 273K bss, 11552K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc4000000 - 0xff800000 ( 952 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc3da8000 ( 61 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB)
[ 0.000000] .init : 0xc0a00000 - 0xc0b00000 (1024 kB)
[ 0.000000] .data : 0xc0b00000 - 0xc0b4d800 ( 310 kB)
[ 0.000000] .bss : 0xc0b4f000 - 0xc0b93714 ( 274 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000018] Switching to timer-based delay loop, resolution 41ns
[ 0.000184] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000426] Console: colour dummy device 80x30
[ 0.000461] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000475] pid_max: default: 32768 minimum: 301
[ 0.000608] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000619] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001314] CPU: Testing write buffer coherency: ok
[ 0.001725] /cpus/cpu@0 missing clock-frequency property
[ 0.001747] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002106] Setting up static identity map for 0x40100000 - 0x40100058
[ 0.002851] smp: Bringing up secondary CPUs ...
[ 0.002868] smp: Brought up 1 node, 1 CPU
[ 0.002878] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[ 0.002884] CPU: All CPU(s) started in SVC mode.
[ 0.003685] devtmpfs: initialized
[ 0.007353] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.007645] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.007675] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.007830] pinctrl core: initialized pinctrl subsystem
[ 0.008855] NET: Registered protocol family 16
[ 0.009402] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.010839] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.010858] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.025254] SCSI subsystem initialized
[ 0.025543] usbcore: registered new interface driver usbfs
[ 0.025606] usbcore: registered new interface driver hub
[ 0.025700] usbcore: registered new device driver usb
[ 0.025958] pps_core: LinuxPPS API ver. 1 registered
[ 0.025970] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.025993] PTP clock support registered
[ 0.026216] Advanced Linux Sound Architecture Driver Initialized.
[ 0.028069] clocksource: Switched to clocksource arch_sys_counter
[ 0.039051] NET: Registered protocol family 2
[ 0.039783] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.039814] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.039838] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.039928] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.039974] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.040189] NET: Registered protocol family 1
[ 0.040785] RPC: Registered named UNIX socket transport module.
[ 0.040803] RPC: Registered udp transport module.
[ 0.040809] RPC: Registered tcp transport module.
[ 0.040814] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.043281] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.052036] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.052998] NFS: Registering the id_resolver key type
[ 0.053047] Key type id_resolver registered
[ 0.053056] Key type id_legacy registered
[ 0.053133] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.057617] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.057640] io scheduler noop registered
[ 0.057647] io scheduler deadline registered
[ 0.057823] io scheduler cfq registered (default)
[ 0.063028] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.130785] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.154457] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 36, base_baud = 1500000) is a U6_16550A
[ 0.176067] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 37, base_baud = 1500000) is a U6_16550A
[ 0.197637] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 38, base_baud = 1500000) is a U6_16550A
[ 0.795303] console [ttyS2] enabled
[ 0.799620] [drm] Initialized
[ 0.806027] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
[ 0.811555] 5 cmdlinepart partitions found on MTD device spi32766.0
[ 0.817815] Creating 5 MTD partitions on "spi32766.0":
[ 0.822982] 0x000000000000-0x0000000f8000 : "uboot"
[ 0.829473] 0x0000000f8000-0x000000100000 : "env"
[ 0.835597] 0x000000100000-0x000000110000 : "dtb"
[ 0.841844] 0x000000110000-0x000000610000 : "kernel"
[ 0.848367] 0x000000610000-0x000002000000 : "rootfs"
[ 0.855218] libphy: Fixed MDIO Bus: probed
[ 0.859973] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[ 0.865789] dwmac-sun8i 1c30000.ethernet: No regulator found
[ 0.871584] dwmac-sun8i 1c30000.ethernet: Will use internal PHY
[ 0.877745] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[ 0.883459] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[ 0.890695] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[ 0.896348] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[ 0.903577] dwmac-sun8i 1c30000.ethernet: COE Type 2
[ 0.908549] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[ 0.915536] libphy: stmmac: probed
[ 0.920937] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.927473] ehci-platform: EHCI generic platform driver
[ 0.933122] ehci-platform 1c1a000.usb: EHCI Host Controller
[ 0.938812] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[ 0.946726] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000
[ 0.978087] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[ 0.985336] hub 1-0:1.0: USB hub found
[ 0.989293] hub 1-0:1.0: 1 port detected
[ 0.993833] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.000152] ohci-platform: OHCI generic platform driver
[ 1.005680] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[ 1.012412] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[ 1.020392] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400
[ 1.093195] hub 2-0:1.0: USB hub found
[ 1.097026] hub 2-0:1.0: 1 port detected
[ 1.104234] usbcore: registered new interface driver usb-storage
[ 1.110928] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[ 1.120469] input: 1c22800.lradc as /devices/platform/soc/1c22800.lradc/input/input0
[ 1.129828] sun6i-rtc 1c20400.rtc: rtc core: registered rtc-sun6i as rtc0
[ 1.136626] sun6i-rtc 1c20400.rtc: RTC enabled
[ 1.141306] i2c /dev entries driver
[ 1.146248] Goodix-TS 0-005d: i2c test failed attempt 1: -6
[ 1.188202] Goodix-TS 0-005d: i2c test failed attempt 2: -6
[ 1.228094] Goodix-TS 0-005d: I2C communication failure: -6
[ 1.234501] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 1.298118] sunxi-mmc 1c0f000.mmc: base:0xc4335000 irq:23
[ 1.358091] sunxi-mmc 1c10000.mmc: base:0xc4339000 irq:24
[ 1.364548] usbcore: registered new interface driver usbhid
[ 1.370213] usbhid: USB HID core driver
[ 1.375726] sun4i-codec 1c22c00.codec: ASoC: /soc/codec-analog@01c23000 not registered
[ 1.383795] sun4i-codec 1c22c00.codec: Failed to register our card
[ 1.391732] NET: Registered protocol family 10
[ 1.398819] Segment Routing with IPv6
[ 1.402557] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.409447] NET: Registered protocol family 17
[ 1.413994] Key type dns_resolver registered
[ 1.418534] Registering SWP/SWPB emulation handler
[ 1.431875] usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 1.439830] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 1.445594] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[ 1.454915] hub 3-0:1.0: USB hub found
[ 1.458952] hub 3-0:1.0: 1 port detected
[ 1.463674] using random self ethernet address
[ 1.468230] using random host ethernet address
[ 1.475116] usb0: HOST MAC 32:cc:9f:3a:8e:c2
[ 1.479602] usb0: MAC 76:4d:08:27:02:20
[ 1.483487] g_cdc gadget: CDC Composite Gadget, version: King Kamehameha Day 2008
[ 1.491014] g_cdc gadget: g_cdc ready
[ 1.497358] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[ 1.508865] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01 00:03:12 UTC (192)
[ 1.517203] vcc5v0: disabling
[ 1.520267] ALSA device list:
[ 1.523236] #0: V3s Audio Codec
[ 1.528701] random: fast init done
[ 1.544273] mmc1: host does not support reading read-only switch, assuming write-enable
[ 1.557687] mmc1: new high speed SD card at address 0001
[ 1.571657] mmcblk1: mmc1:0001 00000 1.83 GiB
[ 1.580893] mmcblk1: p1 p2
[ 1.595109] random: crng init done
[ 4.538331] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 4.556319] VFS: Mounted root (jffs2 filesystem) on device 31:4.
[ 4.563812] devtmpfs: mounted
[ 4.567967] Freeing unused kernel memory: 1024K
FATAL: kernel too old
[ 4.768232] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[ 4.768232]
[ 4.777374] CPU: 0 PID: 1 Comm: linuxrc Not tainted 4.10.15-licheepi-zero-00962-g02a01d8 #18
[ 4.785797] Hardware name: Allwinner sun8i Family
[ 4.790537] [<c010e494>] (unwind_backtrace) from [<c010b230>] (show_stack+0x10/0x14)
[ 4.798281] [<c010b230>] (show_stack) from [<c0358368>] (dump_stack+0x84/0x98)
[ 4.805503] [<c0358368>] (dump_stack) from [<c01a7b84>] (panic+0xdc/0x248)
[ 4.812378] [<c01a7b84>] (panic) from [<c011e358>] (do_exit+0x9d0/0xa00)
[ 4.819074] [<c011e358>] (do_exit) from [<c011f4c4>] (do_group_exit+0x3c/0xd0)
[ 4.826290] [<c011f4c4>] (do_group_exit) from [<c011f568>] (__wake_up_parent+0x0/0x18)
[ 4.834204] Rebooting in 5 seconds..离线
楼主 #2 2019-04-16 14:28:28 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
离线
楼主 #3 2019-04-16 14:31:14 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
Re: 把 Linux4.13 替换成 4.10, 系统提示 FATAL: kernel too old, 然后奔溃
接着进入 buildroot 目录一顿狂搜:
root@ubuntu:/opt/buildroot-2018.08.2# grep "kernel too old" -r .
Binary file ./output/target/lib/ld-2.27.so matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/libc.a matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/csu/libc-start.o matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/elf/ld.so matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/elf/sln matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/elf/ldconfig matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/elf/dl-allobjs.os matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/elf/rtld.os matches
Binary file ./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/elf/librtld.os matches
./output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/sysdeps/unix/sysv/linux/dl-osinfo.h: FATAL ("FATAL: kernel too old\n"); \
./output/build/linux-zero-4.13.y/Documentation/arm/kernel_user_helpers.txt: fprintf(stderr, "can't do atomic operations, kernel too old\n");
./output/build/linux-zero-4.13.y/Documentation/translations/zh_CN/arm/kernel_user_helpers.txt: fprintf(stderr, "can't do atomic operations, kernel too old\n");
./output/build/linux-zero-4.13.y/net/netfilter/xt_hashlimit.c: pr_info("Unknown mode mask %X, kernel too old?\n",
./output/build/linux-headers-zero-4.13.y/Documentation/arm/kernel_user_helpers.txt: fprintf(stderr, "can't do atomic operations, kernel too old\n");
./output/build/linux-headers-zero-4.13.y/Documentation/translations/zh_CN/arm/kernel_user_helpers.txt: fprintf(stderr, "can't do atomic operations, kernel too old\n");
./output/build/linux-headers-zero-4.13.y/net/netfilter/xt_hashlimit.c: pr_info("Unknown mode mask %X, kernel too old?\n",
Binary file ./output/images/rootfs.tar matches
Binary file ./output/host/arm-buildroot-linux-gnueabihf/sysroot/usr/lib/libc.a matches
Binary file ./output/host/arm-buildroot-linux-gnueabihf/sysroot/sbin/sln matches
Binary file ./output/host/arm-buildroot-linux-gnueabihf/sysroot/sbin/ldconfig matches
Binary file ./output/host/arm-buildroot-linux-gnueabihf/sysroot/lib/ld-2.27.so matches
./dl/linux/git/Documentation/arm/kernel_user_helpers.txt: fprintf(stderr, "can't do atomic operations, kernel too old\n");
./dl/linux/git/Documentation/translations/zh_CN/arm/kernel_user_helpers.txt: fprintf(stderr, "can't do atomic operations, kernel too old\n");
./dl/linux/git/net/netfilter/xt_hashlimit.c: pr_info("Unknown mode mask %X, kernel too old?\n",
最可疑就是这个 glibc 了 output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/sysdeps/unix/sysv/linux/dl-osinfo.h
离线
楼主 #4 2019-04-16 14:33:57 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
Re: 把 Linux4.13 替换成 4.10, 系统提示 FATAL: kernel too old, 然后奔溃
打开 output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/sysdeps/unix/sysv/linux/dl-osinfo.h
#define DL_SYSDEP_OSCHECK(FATAL) \
do { \
/* Test whether the kernel is new enough. This test is only performed \
if the library is not compiled to run on all kernels. */ \
\
int version = _dl_discover_osversion (); \
if (__glibc_likely (version >= 0)) \
{ \
if (__builtin_expect (GLRO(dl_osversion) == 0, 1) \
|| GLRO(dl_osversion) > version) \
GLRO(dl_osversion) = version; \
\
/* Now we can test with the required version. */ \
if (__LINUX_KERNEL_VERSION > 0 && version < __LINUX_KERNEL_VERSION) \
/* Not sufficent. */ \
FATAL ("FATAL: kernel too old\n"); \
} \
else if (__LINUX_KERNEL_VERSION > 0) \
FATAL ("FATAL: cannot determine kernel version\n"); \
} while (0)错误就是这里报出来的:
/* Now we can test with the required version. */ \
if (__LINUX_KERNEL_VERSION > 0 && version < __LINUX_KERNEL_VERSION) \
/* Not sufficent. */ \
FATAL ("FATAL: kernel too old\n"); \
}
离线
楼主 #5 2019-04-16 14:33:59 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
Re: 把 Linux4.13 替换成 4.10, 系统提示 FATAL: kernel too old, 然后奔溃
打开配置文件 output/build/glibc-glibc-2.27-57-g6c99e37f6fb640a50a3113b2dbee5d5389843c1e/build/config.h
/* Linux specific: minimum supported kernel version. */
#define __LINUX_KERNEL_VERSION (4 * 65536 + 13 * 256 + 0)
/* Override abi-tags ABI version if necessary. */
#define __ABI_TAG_VERSION 4,13,0这下终于知道为什么了，
离线
楼主 #6 2019-04-16 14:38:37 分享评论
楼主 #8 2019-04-16 15:52:02 分享评论
楼主 #9 2019-04-17 08:07:35 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
离线
楼主 #12 2019-04-17 10:18:16 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
Re: 把 Linux4.13 替换成 4.10, 系统提示 FATAL: kernel too old, 然后奔溃
晕哥 说：https://whycan.cn/files/members/3/2019-04-17_080606.png
如果跑 Linux 4.10 系统， 建议用 buildroot 配置时候选 Linux 4.9.x kernel headers
如果选 Linux 4.10.x kernel headers 仍然可能出现一样的 kernel too old 错误然后宕机.
kernel 4.10, 头文件却要选 4.9.x 这有点说不通诶.
应该是最低要求的意思
离线
楼主 #15 2019-05-14 14:10:52 分享评论
- 晕哥
- 管理员
- 注册时间： 2017-09-06
- 已发帖子： 9,342
- 积分： 9202
Re: 把 Linux4.13 替换成 4.10, 系统提示 FATAL: kernel too old, 然后奔溃
晕哥 说：https://whycan.cn/files/members/3/2019-04-17_080606.png
如果跑 Linux 4.10 系统， 建议用 buildroot 配置时候选 Linux 4.9.x kernel headers
如果选 Linux 4.10.x kernel headers 仍然可能出现一样的 kernel too old 错误然后宕机.
下面还有一个手动指定版本的选项（Manually specified Linux version）可以设置具体的小版本号。
刚刚看了一下， 确实有, 多谢指教 ^_^
离线