WhyCan Forum(哇酷开发者社区)

HELLO! BOOT0 is starting!
boot0 version : 2.0.0▒
read dram para.
dram driver version: 1.15
dram size =256MB
0xffffffff
super_standby_flag = 0
Succeed in opening nand flash.
block from 2 to 6
deal block 2
Succeed in reading Boot1 file head.
The size of Boot1 is 0x00068000.
The file stored in 0x00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[       0.147] boot1 version : 2.0.0
[       0.147] script installed early ok
[       0.148] pmu type = 3
[       0.253] bat vol = 1936 mv
[       0.266] axi:ahb:apb=4:2:2
[       0.266] set dcdc2=1400mv, clock=912M successed
[       0.269] key
[       0.281] no key found
[       0.281] flash init start
[       0.281] NB1 : enter NFB_Init
[       0.284] NB1 : enter phy init
[       0.287] [NAND] nand driver(A20) version: 0x0x00000002, 0x0x00000012, data: 0x426fff64 1111692733
[       0.296] get the good blk ratio from hwscan : 870
[       0.301] NB1 : nand phy init ok
[       0.359] NB1 : init ok
[       0.359] flash init finish
[       0.361] fs init ok
[       0.362] fattype FAT16
[       0.364] fs mount ok
[       0.368] nand good_block_ratio=870
[       0.370] storage_type=0
[       0.383] 0
[       0.383] set pc
[       0.383] usbdc_vol = 4000, usbdc_cur = 0
[       0.385] usbpc_vol = 4200, usbpc_cur = 0
[       0.389] init to usb pc
[       0.392] set pc
[       0.475] battery enough
[       0.475] power_start=0x00000000
[       0.475] power trigger
[       0.795] power start detect
[       0.795] power enter detect
[       0.797] vbus insert
[       0.798] usb start detect
[       0.801] usb enter detect
[       0.804] USB Device!!
[       0.806] usb start detect
[       0.932] base bat_cal = 0
[       1.204] usb set dc
[       1.204] set dc
[       5.267] extenal power low go high startup
[       5.267] usb start detect
[       5.268] usb enter detect
[       5.271] USB Device!!
[       5.671] usb set dc
[       5.671] set dc
[       5.875] usb exit detect
[       5.875] power exit detect
[       5.875] usb exit detect
[       5.878] enter standby

HELLO! BOOT0 is starting!
boot0 version : 2.0.0▒
read dram para.
dram driver version: 1.15
dram size =256MB
0xffffffff
super_standby_flag = 0
Succeed in opening nand flash.
block from 2 to 6
deal block 2
Succeed in reading Boot1 file head.
The size of Boot1 is 0x00068000.
The file stored in 0x00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[       0.147] boot1 version : 2.0.0
[       0.147] script installed early ok
[       0.148] pmu type = 3
[       0.252] bat vol = 0 mv
[       0.265] axi:ahb:apb=4:2:2
[       0.265] set dcdc2=1400mv, clock=912M successed
[       0.267] key
[       0.280] no key found
[       0.280] flash init start
[       0.280] NB1 : enter NFB_Init
[       0.283] NB1 : enter phy init
[       0.286] [NAND] nand driver(A20) version: 0x0x00000002, 0x0x00000012, data: 0x426fff64 1111692733
[       0.295] get the good blk ratio from hwscan : 870
[       0.300] NB1 : nand phy init ok
[       0.358] NB1 : init ok
[       0.358] flash init finish
[       0.360] fs init ok
[       0.361] fattype FAT16
[       0.363] fs mount ok
[       0.367] nand good_block_ratio=870
[       0.369] storage_type=0
[       0.382] 0
[       0.382] set pc
[       0.382] usbdc_vol = 4000, usbdc_cur = 0
[       0.384] usbpc_vol = 4200, usbpc_cur = 0
[       0.388] init to usb pc
[       0.391] set pc
[       0.473] battery enough
[       0.474] power_start=0x00000000
[       0.474] pre boot mode
[       0.794] power start detect
[       0.794] power enter detect
[       0.795] usb start detect
[       0.797] usb enter detect
[       0.800] USB Device!!
[       0.923] no battery exist
[       0.923] power exit detect
[       0.924] usb exit detect
[       0.927] key value = 0
[       0.929] recovery key high 40, low 4
[       1.032] show pic finish
[       1.032] load kernel start
[       1.051] load kernel successed
[       1.051] start address = 0x4a000000
[       1.679] power exit detect
[       1.679] usb exit detect
[       1.679

U-Boot 2011.09-rc1-00000-g556d5c7-dirty (Sep 03 2020 - 03:52:29) Allwinner Technology

CPU:   SUNXI Family
Board: SUN7I-EVB
DRAM:  256 MiB
NAND:  NB1 : enter NFB_Init
[NAND] nand driver(A20) version: 0x2, 0x12, data: 12 1207571896
[NAND] set nand_good_block_ratio 870
NB1 : nand phy init ok
NB1 : init ok
2864 MiB
MMC:   SUNXI SD/MMC: 0
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:5-
-name-        -start-       -size-
bootloader  : 8000          10000
env         : 18000         8000
boot        : 20000         8000
rootfs      : 28000         100000
UDISK       : 128000        470000
-----------------------------------
no misc partition is found
Card did not respond to voltage select!
MMC: block number 0x1 exceeds max(0x0)
** Can't read from device 0 **

** Unable to use mmc 0:0 for fatload **
MMC: block number 0x1 exceeds max(0x0)
** Can't read from device 0 **

** Unable to use mmc 0:1 for fatload **
Hit any key to stop autoboot:  0
[NAND]dumy read,chip 0

Starting kernel ...