使用的mangPi R3 SDK 编译的,不能正常显示splash.bmp
提示
Reading 524288 byte(s) (256 page(s)) at offset 0x00080000
Error: compression type 3 not supported
-Boot 2020.07 (Mar 13 2022 - 21:11:31 +0800) Allwinner Technology
CPU: Allwinner F Series (SUNIV)
Model: Allwinner F1C100s Generic Device
DRAM: 64 MiB
MMC: mmc@1c0f000: 0, mmc@1c10000: 1
Setting up a 800x480 lcd console (overscan 0x0)
In: serial
Out: serial
Err: serial
Allwinner mUSB OTG (Peripheral)
Hit any key to stop autoboot: 0
Card did not respond to voltage select!
Card did not respond to voltage select!
unrecognized JEDEC id bytes: ff, c8, 51
Failed to initialize SPI flash at 0:0 (error -2)
List of MTD devices:
* spi-nand0
- device: spi-nand@1
- parent: spi@1c05000
- driver: spi_nand
- type: NAND flash
- block size: 0x20000 bytes
- min I/O: 0x800 bytes
- OOB size: 128 bytes
- OOB available: 4 bytes
- 0x000000000000-0x000008000000 : "spi-nand0"
=========================
Boot Device: spi
Boot Slot 0: empty
Boot Slot 1: spi-nand
=========================
Reading 524288 byte(s) (256 page(s)) at offset 0x00080000
Error: compression type 3 not supported
gpio: pin 134 (gpio 134) value is 1
DFU waiting on SPI-NAND...
musb-hdrc: peripheral reset irq lost!
Booting from SPI-NAND...
Reading 5242880 byte(s) (2560 page(s)) at offset 0x00100000
## Loading kernel from FIT Image at 81000000 ...
Using 'conf@0' configuration
Trying 'kernel@0' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: uncompressed
Data Start: 0x810000cc
Data Size: 4309816 Bytes = 4.1 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80000000
Entry Point: 0x80000000
Hash algo: crc32
Hash value: 9f754ba3
Verifying Hash Integrity ... crc32+ OK
## Loading fdt from FIT Image at 81000000 ...
Using 'conf@0' configuration
Trying 'fdt@0' fdt subimage
Description: Flattened Device Tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8141c4e8
Data Size: 15757 Bytes = 15.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 6c9c69a9
Verifying Hash Integrity ... crc32+ OK
Booting using the fdt blob at 0x8141c4e8
Loading Kernel Image
Loading Device Tree to 817f9000, end 817ffd8c ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0Usage:
bmp info <imageAddr> - display image info
bmp display <imageAddr> [x y] - display image at x,y
=> bmp info 0x80000
There is no valid bmp file at the given address
=>
如何确认nand.img分区里是否有splash.bmp ?挂载后啥也看不到,不像SD卡镜像都能查看各个分区内容
genimage-nand.cfg文件:
flash nand-128M {
pebsize = 128K
numpebs = 1024
minimum-io-unit-size = 2048
}
image sysimage-nand.img {
flash {}
flashtype = "nand-128M"
partition u-boot {
image = "u-boot-sunxi-with-nand-spl.bin"
size = 512K
}
partition splash {
offset = 0x80000
image = "splash.bmp"
size = 512K
}
partition kernel {
offset = 0x100000
image = "kernel.itb"
size = 5M
}
partition rom {
offset = 0x600000
image = "rootfs.squashfs"
}
}
离线
离线
这个问题是图片格式问题，修改为RGB888就行了，原来的是ARGB888，RGB565格式也会提示Error: compression type 3 not supported
=> bmp info 0x80000000
Image size : 251 x 94
Bits per pixel: 32
Compression : 3
=> bmp display 0x80000000
Error: compression type 3 not supported
=> bmp info 0x80000000
Image size : 251 x 94
Bits per pixel: 16
Compression : 3
=> bmp display 0x80000000
Error: compression type 3 not supported
=> bmp info 0x80000000
Image size : 251 x 94
Bits per pixel: 24
Compression : 0
=> bmp display 0x80000000 350 200
离线