楼主 # 2026-09-01 17:45:45 分享评论
楼主 #1 2026-09-01 17:46:37 分享评论
#2 2026-09-02 08:34:58 分享评论
- Gentlepig
- 会员
- 注册时间： 2018-10-24
- 已发帖子： 1,423
- 积分： 1372.5
Re: T153M3-QCX/T153M4-QCX 简易排针开发板
芯片70，板子269，你这板子保熟吗？
离线
#3 2026-09-02 15:30:48 分享评论
- soso
- 会员
- 注册时间： 2022-05-03
- 已发帖子： 169
- 积分： 197
Re: T153M3-QCX/T153M4-QCX 简易排针开发板
为啥不是h136.... 求h136 h135，哈哈哈
离线
楼主 #4 2026-09-11 17:34:42 分享评论
- 晕哥
- 管理员
- 所在地： wechat: whycan_cn
- 注册时间： 2017-09-06
- 已发帖子： 9,515
- 积分： 9207
Re: T153M3-QCX/T153M4-QCX 简易排针开发板
奇怪有一块板启动正常，但是烧录不了：
......
[128]HELLO! BOOT0 is starting!
[131]BOOT0 commit : {0a84c8b0}
[135][pmu]: bus read error
[137]enable vdd sys auto set
[140]fdt err returned -9
[142]not find dvfs config in spl.dts, default vdd_sys set 0.95V
[148]set pll start
[150]set pll end
[152]dram para13 invalid use default para
[156]vaild para:1 select dram para0
[159]ic board init ok
[161]rtc[7] value = 0x6
[163]enable_jtag
[165]set spi freq:50000000
[169]spi sample_mode:0 sample_delay:1f
[173]spinor id is: ef 40 18, read cmd: 6b
[177]DRAM BOOT DRIVE INFO: V0.21
[180]DRAM use external ZQ
[183]DRAM CLK = 933 MHz
[185]DRAM Type = 3 (3:DDR3,4:DDR4)
[215]DRAM SIZE = 256 MBytes, para1 = 30ea, para2 = 1000001, dram_tpr13 = 8207071
[225]DRAM simple test OK.
[227]dram size = 256
[230]set spi freq:50000000
[234]spi sample_mode:0 sample_delay:1f
[238]spinor id is: ef 40 18, read cmd: 6b
[242]Succeed in reading toc file head.
[245]The size of toc is 1ac000.
[319]Entry_name = u-boot
[328]Entry_name = optee
[333]Jump to OPTEE: optee_base = 0x42900000, uboot_base = 0x43500000
M/TC: OP-TEE version: 807754be (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Tue Aug 5 10:07:52 UTC 2025 arm
M/TC: OP-TEE 32bit
[00.516]ns16550_serial serial@2600000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
U-Boot 2023.04-rc4 (Aug 06 2026 - 15:21:00 +0800) Allwinner Technology
U-Boot bsp (Aug 06 2026 - 15:21:00 +0800) Allwinner Technology
14/40 CPU: SUNXI Family
Model: sun8iw22
DRAM: 256 MiB
[00.547]Relocation Offset is: 0c9a3000
Working FDT set to 4de9b310
[00.603]secure enable bit: 0
E/TC:0 fdt_getprop_u32:388 prop trace_level not found
[00.619]CPU=1008MHz, PLL6=600Mhz, AHB=200Mhz, APB1=100Mhz, MBus=480Mhz
[00.625]workmode = 0,storage type = nor
[00.631]sunxi-spif spif@2800000: frequency no in range, use default value 150000000
[00.638]sunxi-spif spif@2800000: sample_mode:aaaaffff sample_delay:aaaaffff
sunxi_get_spif_mode()222 - get dtr_mode_enable fail -13
sunxi_get_spif_mode()231 - get io_mode_enable fail -13
[00.655]sunxi-spif spif@2800000: probe succeed (Version 1.0.0)
[00.660]sunxi-spif spif@2800000: sspi->mode:0x2400 mode:0x0
[00.676]sunxi-spif spif@2800000: spi sample_mode:0 sample_delay:1f
[00.682]sunxi-spif spif@2800000: spif sspi->speed_hz:50000000
SF: Detected w25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
[00.695]sunxi-spif spif@2800000: sunxi_spif_release_bus()
[00.700]set_sunxi_flash_curdev...45:cur_sunxi_flash :spif-nor.sunxi_flash
Core: 165 devices, 24 uclasses, devicetree: separate
WDT: Not starting watchdog@0x02050000
MMC:
[00.719]Loading Environment from SUNXI_FLASH... [00.747]OK
In: serial
Out: serial
Err: serial
[00.752]skip update boot_param
[00.755]update bootcmd
Net: [00.758]No ethernet found.
[00.761]do sunxi preboot
[00.763]root_partition is rootfs
[00.767]set root to /dev/mtdblock4
[00.770]update part info
bmp_name=bootlogo.bmp
[00.774]sunxi bmp info error : unable to open logo file bootlogo.bmp
[00.780]Get sunxi drm device fail!
Working FDT set to 42000000
[00.806]change working_fdt 0x4de9b310 to 0x42000000
[00.813]enable node spi0/spi_board0 error: FDT_ERR_NOTFOUND
[00.823]spinor update sample_mode:0 right_sample_mod:1f
[00.833]update dts
[00.836]Item0 (Map) magic is bad
[01.129]try to update
Hit any key to stop autoboot: 0
[01.463]do sunxi update
## Booting Android Image at 0x40007800 ...
Android's image name: sun8i_arm
Kernel load addr 0x40008000 size 5305 KiB
## Flattened Device Tree blob at 42000000
Booting using the fdt blob at 0x42000000
Working FDT set to 42000000
XIP Kernel Image
Using Device Tree in place at 42000000, end 42042fff
Working FDT set to 42000000
[02.429]can`t not get hyper image base in /chosen/hyper
[02.433]Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.10.198 (xulu@mylinux) (arm-linux-gnueabihf-gcc (GCC) 11.3.1 20220604 [releases/gcc-11 revision 591c0f4b92548e3ae2e8173f4f93984b1c7f62bb], GNU ld (Linaro_Binutils-2022.06) 2.37.20220122) #6 SMP PREEMPT Thu Aug 6 15:25:29 CST 2026
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: sun8iw22
[ 0.000000] printk: bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Reserved memory: created DMA memory pool at 0x42100000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@42100000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x42144000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node e907_rpbuf@42144000, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 24 MiB at 0x4e800000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x00000000420fffff]
[ 0.000000] node 0: [mem 0x0000000042100000-0x00000000424c4fff]
[ 0.000000] node 0: [mem 0x00000000424c5000-0x000000004fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000004fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] percpu: Embedded 15 pages/cpu s30156 r8192 d23092 u61440
[ 0.000000] pcpu-alloc: s30156 r8192 d23092 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02600000 clk_ignore_unused initcall_debug=0 console=ttyAS0,115200 loglevel=8 root=/dev/mtdblock4 rootwait init=/init partitions=boot-resource@mtdblock1:env@mtdblock2:boot@mtdblock3:rootfs@mtdblock4:private@mtdblock5:rootfs_data@mtdblock6:UDISK@mtdblock7 cma=24M snum= coherent_pool=16K ion_carveout_list= boot_type=3 gpt=1 uboot_message=2023.04-rc4 mbr_offset=2080768
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 201196K/262144K available (7168K kernel code, 1674K rwdata, 2572K rodata, 1024K init, 245K bss, 36372K reserved, 24576K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] AW BSP version: 4b15cb14e7, 2025-11-27 13:57:40 +0800
[ 0.000000] sunxi:ccu-ng:[INFO]: ccu: sunxi ccu init OK
[ 0.000000] sunxi:ccu-ng:[INFO]: sunxi ccu common driver version: 1.2.6
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.007973] Switching to timer-based delay loop, resolution 41ns
[ 0.014363] sunxi:hstimer:[INFO]: sun50i timer init:0x7, driver version: 1.1.6
[ 0.021149] clocksource: timer0: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.032019] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.041335] CPU: Testing write buffer coherency: ok
[ 0.046208] pid_max: default: 32768 minimum: 301
[ 0.050898] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.058079] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.066665] /cpus/cpu@0 missing clock-frequency property
[ 0.071109] /cpus/cpu@1 missing clock-frequency property
[ 0.076361] /cpus/cpu@2 missing clock-frequency property
[ 0.081662] /cpus/cpu@3 missing clock-frequency property
[ 0.086926] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093283] Setting up static identity map for 0x40100000 - 0x40100060
[ 0.099191] rcu: Hierarchical SRCU implementation.
[ 0.104748] smp: Bringing up secondary CPUs ...
[ 0.109521] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.110819] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.112052] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.112167] smp: Brought up 1 node, 4 CPUs
[ 0.129325] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.135556] CPU: All CPU(s) started in SVC mode.
[ 0.140598] devtmpfs: initialized
[ 0.164518] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.166768] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.176373] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.184200] pinctrl core: initialized pinctrl subsystem
[ 0.189901] NET: Registered protocol family 16
[ 0.194090] DMA: preallocated 16 KiB pool for atomic coherent allocations
[ 0.200500] thermal_sys: Registered thermal governor 'fair_share'
[ 0.200508] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.205697] thermal_sys: Registered thermal governor 'step_wise'
[ 0.211630] thermal_sys: Registered thermal governor 'user_space'
[ 0.242327] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.255478] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.262538] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.269598] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.276658] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.283717] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.290777] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.297837] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.304896] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.311956] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.319016] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.326084] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.333144] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.340206] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.347266] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.354325] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.361386] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.368446] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.375505] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.382565] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.389625] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.396693] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.403753] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.410812] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.417872] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.424931] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.431991] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.439051] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.446110] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.453170] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.460230] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.467299] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.474359] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.481419] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.488479] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.495538] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.502598] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.509658] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.516717] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.523777] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.530837] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.537905] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.544965] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.552025] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.559084] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.566143] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.573203] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.580263] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.587323] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.594382] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.601442] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.608510] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.615570] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.622629] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.629689] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.636748] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.643808] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.650868] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.657927] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.664987] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.672047] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.679115] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.686174] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.693234] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.700294] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.707354] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.714414] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.721473] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.728533] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.735593] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.742652] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.749721] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.756781] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.763841] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.770900] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.777960] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.785020] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.792079] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.799138] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.806198] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.813258] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.820332] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.827392] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.834452] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.841512] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.848571] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.855631] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.862690] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.869750] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.876810] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.883869] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.890937] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.897997] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.905057] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.912117] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.919176] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.926237] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.933296] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.940356] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.947416] sunxi:ccu-nglosc not stable, 32K clk will use 16M as parent!
[ 0.948788] sunxi:ccu-ng:[INFO]: rtc_ccu: sunxi ccu init OK
[ 0.954605] sunxi:ccu-ng:[INFO]: cpupll_ccu: sunxi ccu init OK
[ 0.959871] sunxi:ccu-ng:[INFO]: sunxi cpupll driver version: 0.0.1
[ 0.966414] sunxi:ccu-ng:[INFO]: r_ccu: sunxi ccu init OK
[ 0.971718] sunxi:ccu-ng:[INFO]: drampll_ccu: sunxi ccu init OK
[ 0.977341] sun8iw22-pll-dram 3130000.drampll_ccu: sunxi:ccu-ngsun8iw22 pll clk init OK
[ 1.005333] SCSI subsystem initialized
[ 1.005645] usbcore: registered new interface driver usbfs
[ 1.008960] usbcore: registered new interface driver hub
[ 1.014242] usbcore: registered new device driver usb
[ 1.019357] mc: Linux media interface: v0.10
[ 1.023618] videodev: Linux video capture interface: v2.00
[ 1.028985] pps_core: LinuxPPS API ver. 1 registered
[ 1.033926] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.042993] PTP clock support registered
[ 1.047182] Advanced Linux Sound Architecture Driver Initialized.
[ 1.058464] sun6i-dma 3001000.dma-controller: sunxi:dmasunxi dma probed, driver version: 1.2.15
[ 1.063052] sunxi:pwmcs-20a0000.pwmcs0:[INFO]: start probe
[ 1.063092] sunxi:pwmcs-20a0000.pwmcs0:[INFO]: chip->pwmcs_num:0
[ 1.073088] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: base is 0, num is 8
[ 1.079667] sunxi:pwmcs-20a0000.pwmcs0:[INFO]: pwmcschip probe success
[ 1.086017] sunxi:pwmcs-20b0000.pwmcs1:[INFO]: start probe
[ 1.086052] sunxi:pwmcs-20b0000.pwmcs1:[INFO]: chip->pwmcs_num:1
[ 1.097115] sunxi:pwmcs-20b0000.pwmcs1:[ERR]: base is 8, num is 8
[ 1.103578] sunxi:pwmcs-20b0000.pwmcs1:[INFO]: pwmcschip probe success
[ 1.110096] sunxi:pwm-20c0000.pwm2:[INFO]: start probe
[ 1.110139] sunxi:pwm-20c0000.pwm2:[WARN]: invalid PWM alias format: pwmcs0
[ 1.121673] sunxi:pwm-20c0000.pwm2:[WARN]: invalid PWM alias format: pwmcs1
[ 1.129222] sunxi:pwm-20c0000.pwm2:[INFO]: pwmchip probe success
[ 1.134889] clocksource: Switched to clocksource arch_sys_counter
[ 1.153444] sunxi:pin-3604000.pinctrl:[INFO]: pinctrl withstand voltage config mode=auto_hard
[ 1.156379] sunxi:pin:[INFO]: sunxi pinctrl core driver version: 1.4.19
[ 1.164775] sunxi:pin-7096500.pinctrl:[INFO]: pinctrl withstand voltage config mode=auto_hard
[ 1.171921] NET: Registered protocol family 2
[ 1.175979] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 1.183863] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 1.191335] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 1.198927] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 1.206200] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.212417] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 1.218884] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 1.225942] NET: Registered protocol family 1
[ 1.231343] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 1.240718] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.242311] ntfs: driver 2.1.32 [Flags: R/W].
[ 1.246994] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.253253] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 1.260106] io scheduler mq-deadline registered
[ 1.264582] io scheduler kyber registered
[ 1.277587] scsi host0: scsi_debug: version 0190 [20200710]
[ 1.277587] dev_size_mb=8, opts=0x0, submit_queues=1, statistics=0
[ 1.284501] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0190 PQ: 0 ANSI: 7
[ 1.292546] sd 0:0:0:0: Power-on or device reset occurred
[ 1.298676] CAN device driver interface
[ 1.301777] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.307745] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.314040] usbcore: registered new interface driver uas
[ 1.319284] sd 0:0:0:0: [sda] 16384 512-byte logical blocks: (8.39 MB/8.00 MiB)
[ 1.326460] usbcore: registered new interface driver usb-storage
[ 1.332340] usbcore: registered new interface driver ums-alauda
[ 1.336429] sd 0:0:0:0: [sda] Write Protect is off
[ 1.338245] usbcore: registered new interface driver ums-cypress
[ 1.342970] sd 0:0:0:0: [sda] Mode Sense: 73 00 10 08
[ 1.348991] usbcore: registered new interface driver ums-datafab
[ 1.359997] usbcore: registered new interface driver ums_eneub6250
[ 1.366149] usbcore: registered new interface driver ums-freecom
[ 1.372114] usbcore: registered new interface driver ums-isd200
[ 1.374074] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 1.378022] usbcore: registered new interface driver ums-jumpshot
[ 1.392571] usbcore: registered new interface driver ums-karma
[ 1.398407] usbcore: registered new interface driver ums-realtek
[ 1.404355] usbcore: registered new interface driver ums-sddr09
[ 1.410261] usbcore: registered new interface driver ums-sddr55
[ 1.416156] usbcore: registered new interface driver ums-usbat
[ 1.416613] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes
[ 1.422207] i2c /dev entries driver
[ 1.431477] usbcore: registered new interface driver uvcvideo
[ 1.437109] USB Video Class driver (1.1.1)
[ 1.441365] sunxi:pin-3604000.pinctrl:[INFO]: Auto power withstand voltage configuration detected, automatically exit!
[ 1.452222] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.457985] usbcore: registered new interface driver usbhid
[ 1.463346] usbhid: USB HID core driver
[ 1.467224] optee: probing for conduit method.
[ 1.471596] optee: revision 3.7 (807754be)
[ 1.472149] optee: initialized driver
[ 1.480329] uart-ng uart-ng0: supply uart not found, using dummy regulator
[ 1.486353] sunxi:uart-ng-uart-ng0:[INFO]: cannot get the TX DMA channel!
[ 1.492905] sunxi:uart-ng-uart-ng0:[INFO]: cannot get the RX DMA channel!
[ 1.499730] sunxi:uart-ng:[INFO]: sunxi uart-ng driver version: 1.1.21
[ 1.506207] uart-ng0: ttyAS0 at MMIO 0x2600000 (irq = 46, base_baud = 1500000) is a SUNXI
[ 1.514326] sunxi:uart-ng-uart-ng0:[INFO]: console setup baud 115200 parity n bits 8, flow n
[ 1.522834] printk: console [ttyAS0] enabled
[ 1.522834] printk: console [ttyAS0] enabled
[ 1.533195] printk: bootconsole [earlycon0] disabled
[ 1.533195] printk: bootconsole [earlycon0] disabled
[ 1.543841] sunxi:rtc:[INFO]: Saving SoC boot-reason: OTHERS
[ 1.554389] sunxi:rtc:[INFO]: Saving SoC boot-reason: HARDREST-BOOT
[ 1.561637] sunxi:rtc-7090000.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 1.572976] sunxi:rtc-7090000.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 1.584227] sunxi:rtc-7090000.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 1.595759] sunxi-rtc 7090000.rtc: registered as rtc0
[ 1.601425] sunxi:rtc-7090000.rtc:[WARN]: Warning: Using internal RC 16M clock source. Time may be inaccurate!
[ 1.612697] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:03:37 UTC (217)
[ 1.614030] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.621793] sunxi:rtc-7090000.rtc:[INFO]: sunxi rtc probed
[ 1.634104] sunxi-wdt 2050000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0), driver version: 1.0.4
[ 1.646295] sunxi:sunxi_spif-2800000.spif:[INFO]: sample_mode:0 sample_delay:1f
[ 1.654914] sunxi:sunxi_spif-2800000.spif:[INFO]: [spi-flash0] mclk 25000000
[ 1.664478] sunxi:sunxi_spif-2800000.spif:[INFO]: [spi-flash0] working clk 80000000
[ 1.674092] sunxi_spif 2800000.spif: w25q128 (16384 Kbytes)
[ 1.682065] 8 sunxipart partitions found on MTD device spif
[ 1.688330] Creating 8 MTD partitions on "spif":
[ 1.693509] 0x000000000000-0x000000200000 : "uboot"
[ 1.705812] 0x000000200000-0x000000220000 : "boot-resource"
[ 1.715786] 0x000000220000-0x000000240000 : "env"
[ 1.725759] 0x000000240000-0x0000007e0000 : "boot"
[ 1.735748] 0x0000007e0000-0x000001070000 : "rootfs"
[ 1.741320] mtd: partition "rootfs" extends beyond the end of device "spif" -- size truncated to 0x820000
[ 1.755729] 0x000001070000-0x000001080000 : "private"
[ 1.761395] mtd: partition "private" is out of reach -- disabled
[ 1.775746] 0x000001080000-0x000001100000 : "rootfs_data"
[ 1.781802] mtd: partition "rootfs_data" is out of reach -- disabled
[ 1.795719] 0x000001100000-0x0000011fc000 : "UDISK"
[ 1.801188] mtd: partition "UDISK" is out of reach -- disabled
[ 1.815740] sunxi:sunxi_spif-2800000.spif:[INFO]: probe succeed (Version 2.0.0)
[ 1.824840] sunxi:g2d_sunxi:[INFO]: [G2D]: current_thread_id=0
[ 1.831513] sunxi:g2d_sunxi:[INFO]: [G2D]: rcq version initialized.major:242
[ 1.839432] sunxi:g2d_sunxi:[INFO]: [G2D]: g2d_module_init
[ 1.845593] [drm] [DSI-PANEL] panel_dsi_init start
[ 1.851097] [drm] [DSI-PANEL] dsi driver regsiter finsh
[ 1.857666] [drm] [PHY] sunxi_dsi_combophy_probe start
[ 1.863790] [drm] [PHY]sunxi_dsi_combophy_probe finish
[ 1.870328] [drm] sunxi_drm_platform_probe start
[ 1.875533] [drm] sunxi_drm_match_add start
[ 1.881185] [drm] sunxi_drm_match_add finish
[ 1.886021] [drm] sunxi_drm_bind start
[ 1.890567] sunxi-drm soc@3000000:sunxi-drm: bound 5507000.phy (ops sunxi_cphy_component_ops)
[ 1.900160] [drm:sunxi_drm_bind] *ERROR* connector conut zero
[ 1.906615] [drm:sunxi_drm_bind] *ERROR* setup bootloader connecting failed.Skip commit_init_connecting.
[ 1.917546] [drm] Initialized sunxi-drm 3.0.0 20230901 for soc@3000000:sunxi-drm on minor 0
[ 1.926946] [drm] sunxi_drm_bind ok
[ 1.931900] awphy u2-phy0: init awphy sysfs for u2-phy0, ret: 0
[ 1.938671] awphy u2-phy1: init awphy sysfs for u2-phy1, ret: 0
[ 1.945339] sunxi-plat-awphy 4100000.phy: Allwinner USB2.0 PHY Version v1.0.0
[ 1.953449] sunxi:gpadc:[INFO]: sunxi_gpadc_init(): 2349: gpadc class register success
[ 1.963260] input: sunxi-rtp as /devices/platform/soc@3000000/208c000.rtp/input/input0
[ 1.972739] sunxi_dram_info module loaded
[ 1.979232] vdd_cpu: supplied by regulator-dummy
[ 1.985055] sunxi:sunxi_sid:[ERR]: Fail to read 'dvfs2_ori' in dts
[ 1.993420] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.003451] cpu cpu0: _opp_add: OPP not supported by regulators (1056000000)
[ 2.011613] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.021604] cpu cpu0: _opp_add: OPP not supported by regulators (1152000000)
[ 2.029771] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.039759] cpu cpu0: _opp_add: OPP not supported by regulators (1248000000)
[ 2.047907] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.057901] cpu cpu0: _opp_add: OPP not supported by regulators (1368000000)
[ 2.066048] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.076035] cpu cpu0: _opp_add: OPP not supported by regulators (1464000000)
[ 2.084060] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.094049] cpu cpu0: _opp_add: OPP not supported by regulators (1512000000)
[ 2.102089] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.112054] cpu cpu0: _opp_add: OPP not supported by regulators (1560000000)
[ 2.120128] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.130092] cpu cpu0: _opp_add: OPP not supported by regulators (1608000000)
[ 2.138151] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.148116] cpu cpu0: _opp_add: OPP not supported by regulators (1704000000)
[ 2.156162] core: _opp_supported_by_regulators: OPP minuV: 0 maxuV: 0, not supported by regulator
[ 2.166124] cpu cpu0: _opp_add: OPP not supported by regulators (1752000000)
[ 2.174235] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.181441] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.188586] cpu cpu0: _set_opp_voltage: failed to set voltage (1100000 1100000 1100000 mV): -19
[ 2.198402] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.205565] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.212691] cpu cpu0: _set_opp_voltage: failed to set voltage (900000 900000 900000 mV): -19
[ 2.222186] cpufreq: __target_index: Failed to change cpu frequency: -19
[ 2.229797] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.236984] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.237342] ATF no support L3 cache partition, please check or update
[ 2.244114] cpu cpu0: _set_opp_voltage: failed to set voltage (1100000 1100000 1100000 mV): -19
[ 2.252018] NET: Registered protocol family 10
[ 2.261146] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.267252] Segment Routing with IPv6
[ 2.273244] sunxi:pwmcs-20a0000.pwmcs0:[ERR]: can't parse pwm device
[ 2.277411] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.284454] cpu cpu0: _set_opp_voltage: failed to set voltage (900000 900000 900000 mV): -19
[ 2.291633] NET: Registered protocol family 17
[ 2.300560] cpufreq: __target_index: Failed to change cpu frequency: -19
[ 2.313123] NET: Registered protocol family 15
[ 2.318125] can: controller area network core
[ 2.323113] NET: Registered protocol family 29
[ 2.328116] can: raw protocol
[ 2.331443] can: broadcast manager protocol
[ 2.336171] can: netlink gateway - max_hops=1
[ 2.341229] Registering SWP/SWPB emulation handler
[ 2.370932] sunxi:sound-common:[WARN]: 326 pacfg_level_trig_init(): pa-pin-msleep1-0 get failed, default 0
[ 2.382107] sunxi:sound-aa:[WARN]: 110 sunxi_aaudio_parse_dma_param(): capture-cma missing, using default value
[ 2.393447] sunxi:sound-aa:[WARN]: 132 sunxi_aaudio_parse_dma_param(): rx-fifo-size miss,using default value
[ 2.404476] sunxi:sound-aa:[WARN]: 166 sunxi_aaudio_parse_dma_param(): adc-txdata miss, no aaudio platform
[ 2.416259] sunxi:sound-mach:[WARN]: 372 asoc_simple_parse_ucfmt(): set data late to default
[ 2.426166] debugfs: Directory 'soc@3000000:codec_plat' with parent 'audiocodec' already present!
[ 2.438044] sunxi-ehci 4300000.ehci1-controller: supply hci not found, using dummy regulator
[ 2.447762] sunxi-ehci 4300000.ehci1-controller: EHCI Host Controller
[ 2.455020] sunxi-ehci 4300000.ehci1-controller: new USB bus registered, assigned bus number 1
[ 2.464954] sunxi-ehci 4300000.ehci1-controller: irq 55, io mem 0x04300000
[ 2.494913] sunxi-ehci 4300000.ehci1-controller: USB 2.0 started, EHCI 1.00
[ 2.502895] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.512185] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.520292] usb usb1: Product: EHCI Host Controller
[ 2.525771] usb usb1: Manufacturer: Linux 5.10.198 ehci_hcd
[ 2.532016] usb usb1: SerialNumber: sunxi-ehci
[ 2.537512] hub 1-0:1.0: USB hub found
[ 2.541745] hub 1-0:1.0: 1 port detected
[ 2.548059] sunxi-ohci 4300400.ohci1-controller: supply hci not found, using dummy regulator
[ 2.557731] sunxi-ohci 4300400.ohci1-controller: OHCI Host Controller
[ 2.564988] sunxi-ohci 4300400.ohci1-controller: new USB bus registered, assigned bus number 2
[ 2.574858] sunxi-ohci 4300400.ohci1-controller: irq 56, io mem 0x04300400
[ 2.649062] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 2.658346] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.666456] usb usb2: Product: OHCI Host Controller
[ 2.671922] usb usb2: Manufacturer: Linux 5.10.198 ohci_hcd
[ 2.678176] usb usb2: SerialNumber: sunxi-ohci
[ 2.683617] hub 2-0:1.0: USB hub found
[ 2.687866] hub 2-0:1.0: 1 port detected
[ 2.693894] sunxi_usb_udc 4200000.udc-controller: sunxi:sunxi_usb_udc UDC Inner DMA Feature - wordaddr: 1, extend: enabled
[ 2.706888] clk: Not disabling unused clocks
[ 2.711682] ALSA device list:
[ 2.715024] #0: audiocodec
[ 2.720971] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.730289] Freeing unused kernel memory: 1024K
[ 2.775088] Run /init as init process
[ 2.779192] with arguments:
[ 2.782513] /init
[ 2.785073] with environment:
[ 2.788589] HOME=/
[ 2.791228] TERM=linux
[ 2.794257] partitions=boot-resource@mtdblock1:env@mtdblock2:boot@mtdblock3:rootfs@mtdblock4:private@mtdblock5:rootfs_data@mtdblock6:UDISK@mtdblock7
[ 2.809566] snum=
[ 2.812108] ion_carveout_list=
[ 2.815928] boot_type=3
[ 2.819055] uboot_message=2023.04-rc4
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Populating /dev using udev: [ 4.002683] udevd[96]: starting version 3.2.11
[ 4.035760] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.043239] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.050629] random: udevd: uninitialized urandom read (16 bytes read)
[ 4.102917] udevd[96]: specified group 'input' unknown
[ 4.109743] udevd[96]: specified group 'kvm' unknown
[ 4.145298] udevd[97]: starting eudev-3.2.11
done
/etc/init.d/S20mdev: line 6: /proc/sys/kernel/hotplug: No such file or directory
create /dev/sda
mkdir: can't create directory '/mnt/usb/': Read-only file system
mount: mounting /dev/sda on /mnt/usb/sda failed: No such file or directory
/etc/mdev/do_mount: line 4: mount.ntfs-3g: command not found
mkdir /mnt/usb/sda
mkdir: can't create directory '/mnt/usb/sda': No such file or directory
/etc/mdev/do_mount: line 11: mount.exfat: command not found
mount: mounting /dev/sda on /mnt/usb/sda failed: No such file or directory
Saving random seed: SKIP (read-only file system detected)
usb0 current mode:
Starting adb: mkdir: can't create directory '/system/': Read-only file system
mkdir: can't create directory '/system/': Read-only file system
ln: /system/bin/sh: No such file or directory
[ 5.902097] file system registered
OK
init adb main
[ 5.945276] read descriptors
Handling main()
[ 5.949199] read strings
/etc/init.d/S50powerkey_display: line 12: powerkey_display: command not found
/etc/init.d/S50powerkey_suspend: line 12: powerkey_suspend: command not found
Starting telnetd: OK
[ 6.064532] blk_update_request: I/O error, dev mtdblock7, sector 0 op 0x0:(READ) flags 0x800 phys_seg 1 prio class 0
[ 6.076416] SQUASHFS error: Failed to read block 0x0: -5
[ 6.082378] unable to read squashfs_super_block
formating /dev/by-name/UDISK to jffs2...
/etc/partition_op.sh: line 34: mkfs.jffs2: command not found
dd: can't open '/tmp/jffs2.img': No such file or directory
[ 6.176455] Too few erase blocks (0)
mount: mounting /dev/by-name/UDISK on /mnt/UDISK failed: Invalid argument
[ 6.285040] sunxi_usb_udc 4200000.udc-controller: supply udc not found, using dummy regulator
Welcome to Allwinner Tina5.0 Platform
Tina5.0 login: root
#
#
#
#
#异常烧录日志：
[736]fes begin commit:{0a84c8b0}
[740][pmu]: bus read error
[743]set pll start
[744]set pll end
[746]dram para13 invalid use default para
[750]vaild para:1 select dram para0
[753]ic board init ok
[755]beign to init dram
[757]DRAM BOOT DRIVE INFO: V0.21
[760]DRAM use external ZQ
[930][AUTO DEBUG] 16bit, 1 rank training success
[991][AUTO DEBUG] row = 14, col = 10, bank = 3, bg = 0
[996][AUTO DEBUG] para1 = 0x30ea, para2 = 0x1, tpr13 = 0x8207071
[1002][SOFT TRAINING] Version: T2.5
[1005]Soft Training Version: T2.5
[1008][SOFT TRAINING] Dram Soft Training Loop1
[1247][SOFT TRAINING] Stable test, dram_clk=480,dram_tpr12=0x13131313,memtest pass
[1281][SOFT TRAINING] Start rdq vref training
[3373][SOFT TRAINING] Highest r vref: 0x4-0x78, high=0x76(766mV), delay=31
[3380][SOFT TRAINING] Max Vref=0x3e, Widest vref is 0x24~0x5c, center=0x40
[3387][SOFT TRAINING] After rdq00 vref training, dram_add[16] = 0x40404040
[3393][SOFT TRAINING] Start rdq vref training
[4289][SOFT TRAINING] Highest r vref: 0x4-0x7a, high=0x78(779mV), delay=29
[4295][SOFT TRAINING] Max Vref=0x38, Widest vref is 0x24~0x58, center=0x3e
[4302][SOFT TRAINING] After rdq01 vref training, dram_add[16] = 0x40403e40
[4309][SOFT TRAINING] Start rdq 1st training
[4328][SOFT TRAINING] Dbyte0 rdq 1st dqs_move:0,range: 0x10~0x23,width=20,center=0x19
[4385][SOFT TRAINING] Dbyte1 rdq 1st dqs_move:0,range: 0xc~0x23,width=24,center=0x17
[4393][SOFT TRAINING] After rdq 1st training, dram_tpr12 = 0x00001719
[4399][SOFT TRAINING] Start wdq vref training
[5872][SOFT TRAINING] Highest w vref: 0x4-0x7c, high=0x7c(1469mV), delay=148
[5879][SOFT TRAINING] Max vref=0x10, Widest vref is 0x4~0x20, center=0x12
[5886][SOFT TRAINING] After wdq vref training, para->dram_add[17] = 0x92
[5907][SOFT TRAINING] Start wdq 1st training
[5933][SOFT TRAINING] Dbyte0 wdq dqs_move:0,range: 0x88~0xa1,width=26,center=0x94
[5968][SOFT TRAINING] Dbyte1 wdq dqs_move:0,range: 0x8c~0xa1,width=22,center=0x96
[5976][SOFT TRAINING] After wdq 1st training, dram_tpr11 = 0x00009694
[5982][SOFT TRAINING] Start rdq 2nd training
[6535][SOFT TRAINING] After rdq 2nd training, dram_tpr12 = 0x00001719
[6541][SOFT TRAINING] After rdq 3th training, dram_tpr12 = 0x00001719
[6548][SOFT TRAINING] Start wdq 2nd training
[7145][SOFT TRAINING] After wdq 2nd training, dram_tpr11 = 0x00009694
[7151][SOFT TRAINING] After wdq 3th training, dram_tpr11 = 0x00009694
[7157][SOFT TRAINING] dram_add[16]=0x40403e40,tpr11=0x00009694,tpr12=0x00001719
[7190][SOFT TRAINING] CLK=933M Stable memtest pass
[7195]DRAM CLK = 933 MHz
[7197]DRAM Type = 3 (3:DDR3,4:DDR4)
[7227]DRAM SIZE = 256 MBytes, para1 = 30ea, para2 = 1000001, dram_tpr13 = 8207071
[7236]DRAM simple test OK.
[7238]rtc[7] value = 0x6
[7241]init dram ok
[11.118]ns16550_serial serial@2600000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
U-Boot 2023.04-rc4 (Aug 06 2026 - 15:20:32 +0800) Allwinner Technology
U-Boot bsp (Aug 06 2026 - 15:20:32 +0800) Allwinner Technology
14/40 CPU: SUNXI Family
Model: sun8iw22
DRAM: 256 MiB
[11.149]Relocation Offset is: 0c928000
Working FDT set to 4de20310
[11.230]secure enable bit: 0
[11.233]CPU=1008MHz, PLL6=600Mhz, AHB=200Mhz, APB1=100Mhz, MBus=480Mhz
[11.239]workmode = 16,storage type = nand
[11.243][mmc]: mmc driver ver uboot2023:2025-04-02 14:45:00
[11.250][mmc]: get sdc_type fail and use default host:tm4.
[11.256][mmc]: Is not Boot mode!
[11.258][mmc]: SUNXI SDMMC Controller Version:0x50530
[11.266][mmc]: 200 MHz...
[11.268][mmc]: sample: 17 - 147(ps)
[11.272][mmc]: ds: 17 - 147(ps)
[11.274]set_sunxi_flash_curdev...45:cur_sunxi_flash :mmc@04022000.sunxi_flash
[11.287][mmc]: mmc 2 cmd timeout 100 status 100
[11.292][mmc]: smc 2 err, cmd 8, RTO
[11.295][mmc]: mmc 2 close bus gating and reset
[11.300][mmc]: mmc 2 cmd timeout 100 status 100
[11.304][mmc]: smc 2 err, cmd 55, RTO
[11.308][mmc]: mmc 2 close bus gating and reset
[11.316][mmc]: mmc 2 cmd timeout 100 status 100
[11.320][mmc]: smc 2 err, cmd 1, RTO
[11.323][mmc]: mmc 2 close bus gating and reset
[11.328]Card did not respond to voltage select! : -110
[11.333]try emmc fail
[11.334]Invalid bus 0 (err=-19)
[11.337]spinand flash probe error
[11.340]try ubi nand fail
[11.344]sunxi-spif spif@2800000: frequency no in range, use default value 150000000
[11.352]sunxi-spif spif@2800000: sample_mode:aaaaffff sample_delay:aaaaffff
sunxi_get_spif_mode()222 - get dtr_mode_enable fail -13
sunxi_get_spif_mode()231 - get io_mode_enable fail -13
[11.368]sunxi-spif spif@2800000: probe succeed (Version 1.0.0)
[11.374]sunxi-spif spif@2800000: sspi->mode:0x2400 mode:0x0
[11.397]sunxi-spif spif@2800000: spif sspi->speed_hz:50000000
[11.794]sunxi-spif spif@2800000: spif update delay param error
[11.799]sunxi-spif spif@2800000: Sample mode:0 start:0 end:0 sample_delay:0xaaaaffff
SF: Detected w25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
[11.826]sunxi-spif spif@2800000: sunxi_spif_release_bus()
[11.831]set_sunxi_flash_curdev...45:cur_sunxi_flash :spif-nor.sunxi_flash
Core: 164 devices, 26 uclasses, devicetree: separate
WDT: Not starting watchdog@0x02050000
MMC: SUNXI SD/MMC: 0
[11.854]Loading Environment from SUNXI_FLASH... [11.858]OK
In: serial
Out: serial
Err: serial
Net: [11.864]No ethernet found.
Hit any key to stop autoboot: 0
sunxi work mode=0x10
[11.872]request gpio for led failed (-2)
run usb efex
buf queue page size = 65536
usb init ok
set address 0xd
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x12
origin_erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
*************MBR DUMP***************
total mbr part 7
part[0] name :boot-resource
part[0] classname :DISK
part[0] addrlo :0x20
part[0] lenlo :0x100
part[0] user_type :32768
part[0] keydata :0
part[0] ro :0
part[1] name :env
part[1] classname :DISK
part[1] addrlo :0x120
part[1] lenlo :0x100
part[1] user_type :32768
part[1] keydata :0
part[1] ro :0
part[2] name :boot
part[2] classname :DISK
part[2] addrlo :0x220
part[2] lenlo :0x2d00
part[2] user_type :32768
part[2] keydata :0
part[2] ro :0
part[3] name :rootfs
part[3] classname :DISK
part[3] addrlo :0x2f20
part[3] lenlo :0x4480
part[3] user_type :32768
part[3] keydata :0
part[3] ro :0
part[4] name :private
part[4] classname :DISK
part[4] addrlo :0x73a0
part[4] lenlo :0x80
part[4] user_type :32768
part[4] keydata :0
part[4] ro :0
part[5] name :rootfs_data
part[5] classname :DISK
part[5] addrlo :0x7420
part[5] lenlo :0x400
part[5] user_type :32768
part[5] keydata :0
part[5] ro :0
part[6] name :UDISK
part[6] classname :DISK
part[6] addrlo :0x7820
part[6] lenlo :0x0
part[6] user_type :0
part[6] keydata :0
part[6] ro :0
need erase flash: 18
[14.843]Item0 (Map) magic is bad
[14.847]erase secure storage: 0 ok
SUNXI_EFEX_MBR_TAG
mbr size = 0x4000
[14.853]logic size : 0x7820 sector(512 byte)
[14.857]flash size : 0x8000 sector(512 byte)
SF: write offset not multiple of erase size
[14.879]write primary GPT success
[14.882]spinor: skip backup GPT
[14.885]update partition map
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
FEX_CMD_fes_verify_value, start 0x120, size high 0x0:low 0x20000
FEX_CMD_fes_verify_value 0x6ec2fd82这个是正常板子的烧录日志：
[837]fes begin commit:{0a84c8b0}
[841][pmu]: bus read error
[844]set pll start
[846]set pll end
[847]dram para13 invalid use default para
[851]vaild para:1 select dram para0
[854]ic board init ok
[857]beign to init dram
[859]DRAM BOOT DRIVE INFO: V0.21
[862]DRAM use external ZQ
[1031][AUTO DEBUG] 16bit, 1 rank training success
[1093][AUTO DEBUG] row = 14, col = 10, bank = 3, bg = 0
[1098][AUTO DEBUG] para1 = 0x30ea, para2 = 0x1, tpr13 = 0x8207071
[1104][SOFT TRAINING] Version: T2.5
[1107]Soft Training Version: T2.5
[1110][SOFT TRAINING] Dram Soft Training Loop1
[1349][SOFT TRAINING] Stable test, dram_clk=480,dram_tpr12=0x13131313,memtest pass
[1383][SOFT TRAINING] Start rdq vref training
[3459][SOFT TRAINING] Highest r vref: 0x6-0x78, high=0x74(753mV), delay=31
[3466][SOFT TRAINING] Max Vref=0x40, Widest vref is 0x24~0x62, center=0x43
[3473][SOFT TRAINING] After rdq00 vref training, dram_add[16] = 0x40404043
[3480][SOFT TRAINING] Start rdq vref training
[4331][SOFT TRAINING] Highest r vref: 0x6-0x78, high=0x74(753mV), delay=29
[4338][SOFT TRAINING] Max Vref=0x36, Widest vref is 0x2a~0x50, center=0x3d
[4345][SOFT TRAINING] After rdq01 vref training, dram_add[16] = 0x40403d43
[4352][SOFT TRAINING] Start rdq 1st training
[4373][SOFT TRAINING] Dbyte0 rdq 1st dqs_move:0,range: 0x10~0x25,width=22,center=0x1a
[4427][SOFT TRAINING] Dbyte1 rdq 1st dqs_move:0,range: 0xe~0x23,width=22,center=0x18
[4434][SOFT TRAINING] After rdq 1st training, dram_tpr12 = 0x0000181a
[4441][SOFT TRAINING] Start wdq vref training
[5876][SOFT TRAINING] Highest w vref: 0x4-0x7c, high=0x7c(1469mV), delay=148
[5883][SOFT TRAINING] Max vref=0x8, Widest vref is 0x4~0x24, center=0x14
[5890][SOFT TRAINING] After wdq vref training, para->dram_add[17] = 0x94
[5912][SOFT TRAINING] Start wdq 1st training
[5938][SOFT TRAINING] Dbyte0 wdq dqs_move:0,range: 0x88~0xa1,width=26,center=0x94
[5968][SOFT TRAINING] Dbyte1 wdq dqs_move:0,range: 0x8a~0xa1,width=24,center=0x95
[5975][SOFT TRAINING] After wdq 1st training, dram_tpr11 = 0x00009594
[5982][SOFT TRAINING] Start rdq 2nd training
[6535][SOFT TRAINING] After rdq 2nd training, dram_tpr12 = 0x0000181a
[6542][SOFT TRAINING] After rdq 3th training, dram_tpr12 = 0x0000181a
[6548][SOFT TRAINING] Start wdq 2nd training
[7136][SOFT TRAINING] After wdq 2nd training, dram_tpr11 = 0x00009594
[7142][SOFT TRAINING] After wdq 3th training, dram_tpr11 = 0x00009594
[7148][SOFT TRAINING] dram_add[16]=0x40403d43,tpr11=0x00009594,tpr12=0x0000181a
[7182][SOFT TRAINING] CLK=933M Stable memtest pass
[7186]DRAM CLK = 933 MHz
[7189]DRAM Type = 3 (3:DDR3,4:DDR4)
[7219]DRAM SIZE = 256 MBytes, para1 = 30ea, para2 = 1000001, dram_tpr13 = 8207071
[7228]DRAM simple test OK.
[7230]rtc[7] value = 0x1
[7232]init dram ok
[11.095]ns16550_serial serial@2600000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
U-Boot 2023.04-rc4 (Aug 06 2026 - 15:20:32 +0800) Allwinner Technology
U-Boot bsp (Aug 06 2026 - 15:20:32 +0800) Allwinner Technology
14/40 CPU: SUNXI Family
Model: sun8iw22
DRAM: 256 MiB
[11.126]Relocation Offset is: 0c928000
Working FDT set to 4de20310
[11.207]secure enable bit: 0
[11.209]CPU=1008MHz, PLL6=600Mhz, AHB=200Mhz, APB1=100Mhz, MBus=480Mhz
[11.216]workmode = 16,storage type = nand
[11.220][mmc]: mmc driver ver uboot2023:2025-04-02 14:45:00
[11.227][mmc]: get sdc_type fail and use default host:tm4.
[11.232][mmc]: Is not Boot mode!
[11.235][mmc]: SUNXI SDMMC Controller Version:0x50530
[11.243][mmc]: 200 MHz...
[11.245][mmc]: sample: 17 - 147(ps)
[11.248][mmc]: ds: 17 - 147(ps)
[11.251]set_sunxi_flash_curdev...45:cur_sunxi_flash :mmc@04022000.sunxi_flash
[11.264][mmc]: mmc 2 cmd timeout 100 status 100
[11.268][mmc]: smc 2 err, cmd 8, RTO
[11.272][mmc]: mmc 2 close bus gating and reset
[11.277][mmc]: mmc 2 cmd timeout 100 status 100
[11.281][mmc]: smc 2 err, cmd 55, RTO
[11.284][mmc]: mmc 2 close bus gating and reset
[11.293][mmc]: mmc 2 cmd timeout 100 status 100
[11.297][mmc]: smc 2 err, cmd 1, RTO
[11.300][mmc]: mmc 2 close bus gating and reset
[11.305]Card did not respond to voltage select! : -110
[11.309]try emmc fail
[11.311]Invalid bus 0 (err=-19)
[11.314]spinand flash probe error
[11.317]try ubi nand fail
[11.321]sunxi-spif spif@2800000: frequency no in range, use default value 150000000
[11.328]sunxi-spif spif@2800000: sample_mode:aaaaffff sample_delay:aaaaffff
sunxi_get_spif_mode()222 - get dtr_mode_enable fail -13
sunxi_get_spif_mode()231 - get io_mode_enable fail -13
[11.345]sunxi-spif spif@2800000: probe succeed (Version 1.0.0)
[11.350]sunxi-spif spif@2800000: sspi->mode:0x2400 mode:0x0
[11.880]sunxi-spif spif@2800000: spif sspi->speed_hz:50000000
[12.319]sunxi-spif spif@2800000: Sample mode:0 start:0 end:63 sample_delay:0x1f
SF: Detected w25q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
[12.991]sunxi-spif spif@2800000: sunxi_spif_release_bus()
[12.996]set_sunxi_flash_curdev...45:cur_sunxi_flash :spif-nor.sunxi_flash
Core: 171 devices, 27 uclasses, devicetree: separate
WDT: Not starting watchdog@0x02050000
MMC: SUNXI SD/MMC: 0
[13.020]Loading Environment from SUNXI_FLASH... [13.024]OK
In: serial
Out: serial
Err: serial
Net: [13.030]No ethernet found.
Hit any key to stop autoboot: 0
sunxi work mode=0x10
[13.038]request gpio for led failed (-2)
run usb efex
buf queue page size = 65536
usb init ok
set address 0x14
SUNXI_EFEX_ERASE_TAG
erase_flag = 0x12
origin_erase_flag = 0x1
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
the 0 mbr table is ok
*************MBR DUMP***************
total mbr part 7
part[0] name :boot-resource
part[0] classname :DISK
part[0] addrlo :0x20
part[0] lenlo :0x100
part[0] user_type :32768
part[0] keydata :0
part[0] ro :0
part[1] name :env
part[1] classname :DISK
part[1] addrlo :0x120
part[1] lenlo :0x100
part[1] user_type :32768
part[1] keydata :0
part[1] ro :0
part[2] name :boot
part[2] classname :DISK
part[2] addrlo :0x220
part[2] lenlo :0x2d00
part[2] user_type :32768
part[2] keydata :0
part[2] ro :0
part[3] name :rootfs
part[3] classname :DISK
part[3] addrlo :0x2f20
part[3] lenlo :0x4480
part[3] user_type :32768
part[3] keydata :0
part[3] ro :0
part[4] name :private
part[4] classname :DISK
part[4] addrlo :0x73a0
part[4] lenlo :0x80
part[4] user_type :32768
part[4] keydata :0
part[4] ro :0
part[5] name :rootfs_data
part[5] classname :DISK
part[5] addrlo :0x7420
part[5] lenlo :0x400
part[5] user_type :32768
part[5] keydata :0
part[5] ro :0
part[6] name :UDISK
part[6] classname :DISK
part[6] addrlo :0x7820
part[6] lenlo :0x0
part[6] user_type :0
part[6] keydata :0
part[6] ro :0
need erase flash: 18
[16.012]Item0 (Map) magic is bad
[16.015]erase secure storage: 0 ok
SUNXI_EFEX_MBR_TAG
mbr size = 0x4000
[16.021]logic size : 0x7820 sector(512 byte)
[16.025]flash size : 0x8000 sector(512 byte)
SF: write offset not multiple of erase size
[16.302]write primary GPT success
[16.305]spinor: skip backup GPT
[16.308]update partition map
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
FEX_CMD_fes_verify_value, start 0x120, size high 0x0:low 0x20000
FEX_CMD_fes_verify_value 0xf29ba354
FEX_CMD_fes_verify_value, start 0x220, size high 0x0:low 0x54d000
FEX_CMD_fes_verify_value 0x8b6d1230
FEX_CMD_fes_verify_value, start 0x2f20, size high 0x0:low 0x503000
FEX_CMD_fes_verify_value 0x1e18c8cc
bootfile_mode=4
SUNXI_EFEX_BOOT1_TAG
boot1 size = 0x1ac000, max size = 0x400000
[17.474]uboot size = 0x1ac000
[17.477]storage type = 3
SF: write offset not multiple of erase size
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
bootfile_mode=4
SUNXI_EFEX_BOOT0_TAG
boot0 size = 0x10000
[17.918]storage type = 3
boot_info->frequency:2faf080
FEX_CMD_fes_verify_status
FEX_CMD_fes_verify last err=0
sunxi_efex_next_action=2
exit usb
next work 2
SUNXI_UPDATE_NEXT_ACTION_REBOOT
......离线
#5 2026-09-11 20:00:31 分享评论
- ₩υ二胖_cf2c0d29
- 会员
- 注册时间： 2026-09-11
- 已发帖子： 1
- 积分： 1
Re: T153M3-QCX/T153M4-QCX 简易排针开发板
@晕哥
实在不行就直接换个nand试试
离线
楼主 #6 2026-09-11 21:51:55 分享评论
感谢为中文互联网持续输出优质内容的各位老铁们。
QQ: 516333132, 微信(wechat): whycan_cn (哇酷网/挖坑网/填坑网) service@whycan.cn
东莞哇酷科技有限公司开发
东莞哇酷科技有限公司开发