- 首页
- » 搜索
- » 落日余晖 发表的帖子
页次： 1
#2 Re: 全志 SOC » 简单的点灯求助 » 2022-11-25 15:37:00
在小智S3开发板上添加两个GPIO PB12/PB13 (Linux4.13), 但是却失败, 大家帮我找下问题
https://whycan.com/t_2233.html#p16357
echo 44 > /sys/class/gpio/export
echo out > /sys/class/gpio/gpio44/direction
echo 1 > /sys/class/gpio/gpio44/value ### PB12 输出高电平
echo 0 > /sys/class/gpio/gpio44/value ### PB12 输出低电平
#3 Re: 全志 SOC » 发一个 荔枝派zero 能跑的 camdroid 固件, ov5647摄像头， 视频效果相当暗，很难看清楚. » 2022-07-20 21:52:16
HELLO! BOOT0 is starting!
get_ifm reg_val=7
setting pmu vol system core 1.1 v
===i2c gpio === 22777777
axp read fail, maybe no pmu
set pmu vol failed,maybe no pmu
DRAM DRIVE INFO: V0.7
DRAM Type = 2 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
DRAM CLK = 360 MHz
DRAM zq value: 000039bb
DRAM size = 64 MB
Succeed in reading Boot1 file head.
Jump to secend Boot.
[ 0.093]
U-Boot 2011.09-rc1-dirty (Jun 16 2015 - 13:24:18) Allwinner Technology
[ 0.101]version: 1.1.0
[ 0.106]pmbus:
===i2c gpio === 22777777
ready
axp read error
probe axp20x failed
axp_probe fail,run clock=1008
set power on vol to default
axp_set_power_supply_output dcdc2_vol = 1200
axp set dcdc2_vol to 1200 failed
axp_set_power_supply_output dcdc3_vol = 3300
axp set dcdc3_vol to 3300 failed
axp_set_power_supply_output aldo2_vol = 2500
axp set aldo2_vol to 2500 failed
axp_set_power_supply_output aldo3_vol = 3000
axp set aldo3_vol to 3000 failed
axp_set_power_supply_output ldo1_vol = 3300
axp set ldo1_vol to 3300 failed
axp_set_power_supply_output ldo2_vol = 3000
axp set ldo2_vol to 3000 failed
[ 0.166]DRAM: 64 MiB
[debug_jaosn]:use the clock in sys_config
OK
[ 0.188]sunxi flash init ok
hello @flash_speed=1
env_relocate_spec storage_type = 3
In: serial
Out: serial
Err: serial
WORK_MODE_BOOT
read bootlogo partition successful,start_block=0x6420,rblock=0x100 ,ret=256
Use decode 1x1 sampling
sunxi_read_bootlogo: jpg convert argb
[ 0.373]Hit any key to stop autoboot: 0
read boot or recovery all
[ 0.659]sunxi flash read :offset 4000, 4194815 bytes OK
[ 0.665]ready to boot
[ 0.667]
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.39 (avr32@ubuntu) (gcc version 4.6.3 20120201 (prerelease) (crosstool-NG linaro-1.13.1-2012.02-20120222 - Linaro GCC 2012.02) ) #8 Tue Jul 19 15:30:10 CST 2022
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun8i
[ 0.000000] Initialized persistent memory from 41d20800-41d307ff
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat c04e60e4, node_mem_map c0580000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] script_init enter!
[ 0.000000] script_init exit!
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/nor1 init=/init loglevel=8 partitions= mac_addr= uid=1234567890 kmemleak=on fb_base=0x41b00000 boot_type=3 config_size=32360
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 64MB = 64MB total
[ 0.000000] Memory: 30164k/30164k available, 35372k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc047f000 (4572 kB)
[ 0.000000] .init : 0xc047f000 - 0xc04a2000 ( 140 kB)
[ 0.000000] .data : 0xc04a2000 - 0xc04e6820 ( 275 kB)
[ 0.000000] .bss : 0xc04e6844 - 0xc057fde4 ( 614 kB)
[ 0.000000] NR_IRQS:544
[ 0.000000] 524 ahb1 set parent pll_periph0d2
[ 0.000000] Architected local timer running at 24.00MHz.
[ 0.000000] Switching to timer-based delay loop
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000156] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[ 0.000178] pid_max: default: 32768 minimum: 301
[ 0.000316] Mount-cache hash table entries: 512
[ 0.000835] CPU: Testing write buffer coherency: ok
[ 0.001102] Setting up static identity map for 0x4035c420 - 0x4035c478
[ 0.001772] devtmpfs: initialized
[ 0.003642] pinctrl core: initialized pinctrl subsystem
[ 0.004137] NET: Registered protocol family 16
[ 0.004540] DMA: preallocated 128 KiB pool for atomic coherent allocations
[ 0.004593] script_sysfs_init success
[ 0.004628] sunxi_dump_init success
[ 0.005348] gpiochip_add: registered GPIOs 0 to 223 on device: sunxi-pinctrl
[ 0.006237] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[ 0.006591] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[ 0.007451] persistent_ram: found existing buffer, size 54284, start 54284
[ 0.245677] console [ram-1] enabled
[ 0.246187] [sunxi-module]: [sunxi-module.0] probe success
[ 0.246400] axp driver uning configuration failed(801)
[ 0.246591] axp driver uning configuration failed(808)
[ 0.246969] Not Found clk pll_isp in script
[ 0.247085] Not Found clk pll_video in script
[ 0.247275] Not Found clk pll_ve in script
[ 0.247379] Not Found clk pll_periph0 in script
[ 0.247570] Not Found clk pll_de in script
[ 0.247674] sunxi_default_clk_init
[ 0.247778] try to set pll6ahb1 to 200000000
[ 0.247978] Error not get clk pll6ahb1
[ 0.248086] Error not get clk pll6ahb1try to set ahb1 to 200000000
[ 0.248304] try to set apb1 to 100000000
[ 0.248818] ===fe3o4==== sunxi_root_procfs_attach ret:0
[ 0.252395] bio: create slab <bio-0> at 0
[ 0.252854] pwm module init!
[ 0.255070] SCSI subsystem initialized
[ 0.255403] usbcore: registered new interface driver usbfs
[ 0.255656] usbcore: registered new interface driver hub
[ 0.255902] usbcore: registered new device driver usb
[ 0.256238] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[ 0.256347] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[ 0.257205] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x34)
[ 0.257331] axp20_board 0-0034: failed reading at 0x03
[ 0.257523] [AXP20-MFD] try to read chip id failed!
[ 0.257626] axp mfd register failed
[ 0.257743] axp20_board: probe of 0-0034 failed with error -70
[ 0.257980] Linux video capture interface: v2.00
[ 0.258187] gpiochip_add: gpios 1024..1028 (axp_pin) failed to register
[ 0.258381] axp pinctrl used,skip
[ 0.258797] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.259893] cfg80211: Calling CRDA to update world regulatory domain
[ 0.260973] Switching to clocksource arch_sys_counter
[ 0.269909] NET: Registered protocol family 2
[ 0.269909] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.269909] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.269909] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.270164] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.270360] TCP: reno registered
[ 0.270472] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270588] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.271056] NET: Registered protocol family 1
[ 0.271374] Unpacking initramfs...
[ 0.286142] Freeing initrd memory: 220K
[ 0.286476] [pm]aw_pm_init!
[ 0.286585] standby_mode = 1.
[ 0.286689] wakeup src cnt is : 3.
[ 0.286885] pmu name: pmu1_para .
[ 0.286995] pmu1_enable = 0x1.
[ 0.287100] pmux_id = 0x1.
[ 0.287291] pmu name: pmu2_para .
[ 0.287394] config_pmux_para: script_parser_fetch err.
[ 0.287498] pmu2_enable = 0x0.
[ 0.287691] add_sys_pwr_dm: get ldo name failed
[ 0.287794] add_sys_pwr_dm: get ldo name failed
[ 0.287897] add_sys_pwr_dm: get ldo name failed
[ 0.288084] add_sys_pwr_dm: get ldo name failed
[ 0.288188] add_sys_pwr_dm: get ldo name failed
[ 0.288378] add_sys_pwr_dm: get ldo name failed
[ 0.288481] add_sys_pwr_dm: get ldo name failed
[ 0.288586] add_sys_pwr_dm: get ldo name failed
[ 0.288776] add_sys_pwr_dm: get ldo name failed
[ 0.288879] add_sys_pwr_dm: get ldo name failed
[ 0.289068] after inited: sys_mask config = 0x0.
[ 0.289172] dynamic_standby enalbe = 0x0.
[ 0.289331] sunxi_reg_init enter
[ 0.291422] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.291583] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.291954] msgmni has been set to 59
[ 0.293009] io scheduler noop registered
[ 0.293127] io scheduler deadline registered
[ 0.293394] io scheduler cfq registered (default)
[ 0.293896] [DISP]disp_module_init
[ 0.294482] cmdline,disp=
[ 0.295097] rotation_sw module is config as no used
[ 0.295231] [DISP] disp_get_rotation_sw,line:68:disp 0 out of range? g_rot_sw=0
[ 0.295524] [DISP] disp_init_connections,line:289:NULL pointer: 0, 0
[ 0.313398] [DISP] disp_sys_power_enable,line:387:some error happen, fail to get regulator
[ 0.313714] [DISP] disp_sys_gpio_set_value,line:374:OSAL_GPIO_DevWRITE_ONEPIN_DATA, hdl is NULL
[ 0.314714] [DISP]disp_module_init finish
[ 0.315109] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[ 0.315315] sw_uart_get_devinfo()1503 - uart2 has no uart_regulator.
[ 0.315857] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[ 0.316066] sw_uart_pm()890 - uart0 clk is already enable
[ 0.316184] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[ 0.412258] console [ttyS0] enabled
[ 1.149091] uart: probe of uart2 failed with error -22
[ 1.156211] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
[ 1.164059] spi spi0: master is unqueued, this is deprecated
[ 1.170749] m25p_probe()967 - Use the Dual Mode Read.
[ 1.176542] NorFlash ID: 0xef4018 - 0x0
[ 1.181019] m25p80 spi0.0: found W25q128, expected at25df641
[ 1.187423] m25p80 spi0.0: W25q128 (16384 Kbytes)
[ 1.194324] @@@[debug_jaosn]: Invalid partitions count: 4 9
[ 1.201105] Creating 8 MTD partitions on "spi0.0":
[ 1.206535] 0x000000000000-0x000000040000 : "uboot"
[ 1.213074] 0x000000040000-0x000000440000 : "boot"
[ 1.219360] 0x000000440000-0x000000c40000 : "system"
[ 1.225991] 0x000000c40000-0x000000cc0000 : "cfg"
[ 1.232242] 0x000000cc0000-0x000000ce0000 : "boot_logo"
[ 1.239092] 0x000000ce0000-0x000000d00000 : "shutdown_logo"
[ 1.246556] 0x000000d00000-0x000000d10000 : "env"
[ 1.252967] 0x000000d10000-0x000000d20000 : "private"
[ 1.261097] Failed to alloc md5
[ 1.264768] eth0: Use random mac address
[ 1.269363] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.296870] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.305999] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[ 1.314733] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[ 1.340040] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[ 1.347512] hub 1-0:1.0: USB hub found
[ 1.351841] hub 1-0:1.0: 1 port detected
[ 1.356716] sunxi-ehci sunxi-ehci.1: remove, state 1
[ 1.362489] usb usb1: USB disconnect, device number 1
[ 1.660245] sunxi-ehci sunxi-ehci.1: USB bus 1 deregistered
[ 1.676745] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.703822] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.712552] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 1
[ 1.721215] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[ 1.784636] hub 1-0:1.0: USB hub found
[ 1.788918] hub 1-0:1.0: 1 port detected
[ 1.793866] sunxi-ohci sunxi-ohci.1: remove, state 1
[ 1.799515] usb usb1: USB disconnect, device number 1
[ 1.805896] sunxi-ohci sunxi-ohci.1: USB bus 1 deregistered
[ 1.822332] Initializing USB Mass Storage driver...
[ 1.828010] usbcore: registered new interface driver usb-storage
[ 1.834801] USB Mass Storage support registered.
[ 1.840426] file system registered
[ 1.845712] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.853531] android_usb gadget: Number of LUNs=1
[ 1.858841] lun0: LUN: removable file: (no medium)
[ 1.864824] android_usb gadget: android_usb ready
[ 1.870392] sunxikbd_script_init: key para not found, used default para.
[ 1.878995] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[ 1.886769] sunxi cedar version 0.1
[ 1.890901] [cedar]: install start!!!
[ 1.895327] [cedar]: install end!!!
[ 1.899765] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 1.908633] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 1.917564] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 1.926280] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 1.935011] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 1.943639] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 1.952361] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 1.961429] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[ 1.968688] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[ 1.980154] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[ 1.987878] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[ 1.994195] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
[ 2.004049] [mmc]: SD/MMC/SDIO Host Controller Driver(v1.114 2015-6-2 10:21) Compiled in Jul 18 2022 at 16:53:41
[ 2.015623] [mmc]: get mmc0's sdc_power failed
[ 2.020678] [mmc]: MMC host used card: 0x1, boot card: 0x1, io_card 0
[ 2.028759] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.039805] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.049951] sunxi_leds_fetch_sysconfig_para leds is not used in config
[ 2.057423] =========script_get_err============
[ 2.062583] [mmc]: sdc0 power_supply is null
[ 2.068955] usbcore: registered new interface driver usbhid
[ 2.075321] usbhid: USB HID core driver
[ 2.080064] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.090872] ashmem: initialized
[ 2.094699] logger: created 256K log 'log_main'
[ 2.100146] logger: created 32K log 'log_events'
[ 2.105490] logger: created 32K log 'log_radio'
[ 2.110871] logger: created 32K log 'log_system'
[ 2.117504] script_get_item return audio_pa_ctrl type err
[ 2.124663] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 2.133249] asoc: sndcodec <-> sunxi-codec mapping ok
[ 2.139050] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 2.147429] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.159798] TCP: cubic registered
[ 2.163646] NET: Registered protocol family 17
[ 2.168996] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 2.177863] ThumbEE CPU extension supported.
[ 2.183927] Registering SWP/SWPB emulation handler
[ 2.190389] [mmc]: sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.201680] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 2.210837] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 2.219377] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 2.229224] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 2.237853] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 8, RTO !!
[ 2.246099] *******************Try sdio*******************
[ 2.252438] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 2.261054] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.269377] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 2.278183] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.286580] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 2.295296] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.303715] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:03 UTC (3)
[ 2.312514] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.320759] *******************Try sd *******************
[ 2.327755] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.336804] [wifi module_pm]: failed to fetch wifi configuration!
[ 2.343830] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.352268] [wifi module_pm]: regulator on.
[ 2.357011] [wifi_pm]: no wifi used in configuration
[ 2.362627] ALSA device list:
[ 2.366098] #0: audiocodec
[ 2.369900] Freeing init memory: 140K
[ 2.374119] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.384661] init: skipping insecure file '/default.prop'
[ 2.390749] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.399186] *******************Try mmc*******************
[ 2.405326] [mmc]: sdc0 set ios: clk 400000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.415899] init: skipping insecure file '/init.rc'
[ 2.421920] init: /init.rc: 127: invalid option 'root'
[ 2.427785] init: skipping insecure file '/init.sun8i.rc'
[ 2.434395] init: /init.sun8i.rc: 54: invalid option 'root'
[ 2.440728] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 1, RTO !!
[ 2.449072] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.459120] init: skipping insecure file 'init.sun8i.usb.rc'
[ 2.466197] init: command 'loglevel' r=0
[ 2.470905] [mmc]: sdc0 power_supply is null
[ 2.477280] init: skipping insecure file '/ueventd.rc'
[ 2.484343] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.494291] init: command 'export' r=0
[ 2.498595] init: command 'export' r=0
[ 2.503227] init: skipping insecure file '/ueventd.sun8i.rc'
[ 2.510114] init: command 'export' r=0
[ 2.514425] init: command 'export' r=0
[ 2.518833] init: command 'symlink' r=0
[ 2.529414] [mmc]: sdc0 power_supply is null
[ 2.545712] init: command 'symlink' r=0
[ 2.560130] [mmc]: sdc0 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.570832] init: command 'symlink' r=0
[ 2.575300] init: command 'mkdir' r=0
[ 2.579544] init: command 'mkdir' r=0
[ 2.590305] init: command 'mkdir' r=0
[ 2.600314] init: command 'mkdir' r=-2
[ 2.604616] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 2.614188] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 2.622700] [mmc]: sdc0 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.639747] init: processing action 0x1a10138 (init)
[ 2.645579] init: command 'export' r=0
[ 2.649848] init: command 'export' r=0
[ 2.655334] init: command 'export' r=0
[ 2.660790] [mmc]: sdc0 set ios: clk 300000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.671155] init: command 'export' r=0
[ 2.675457] init: processing action 0x1a0ec28 (early-fs)
[ 2.682737] init: command 'mkdir' r=0
[ 2.687002] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 8, RTO !!
[ 2.695275] *******************Try sdio*******************
[ 2.701656] init: command 'mkdir' r=0
[ 2.705823] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.714231] init: command 'mkdir' r=0
[ 2.718396] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.726752] init: processing action 0x1a113d8 (console_init)
[ 2.733144] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.741795] init: command 'console_init' r=0
[ 2.746651] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 2.755006] *******************Try sd *******************
[ 2.761153] init: processing action 0x1a0ef30 (fs)
[ 2.766655] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.775054] init: command 'wait' r=0
[ 2.779207] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.788171] init: command 'setupfs' r=1
[ 2.792701] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.801144] init: out of loopback devices source = /dev/block/mtdblock2
[ 2.808687] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 2.817128] *******************Try mmc*******************
[ 2.823247] [mmc]: sdc0 set ios: clk 300000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.833619] init: out of loopback devices target = /system
[ 2.839813] init: out of loopback devices system = squashfs
[ 2.846367] init: out of loopback devices options = (null)
[ 2.852570] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 1, RTO !!
[ 2.860904] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.872502] [mmc]: sdc0 power_supply is null
[ 2.879524] init: command 'mount' r=0
[ 2.884875] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.894769] init: command 'wait' r=0
[ 2.898950] init: out of loopback devices source = /dev/block/mtdblock3
[ 2.906426] [mmc]: sdc0 power_supply is null
[ 2.911364] init: out of loopback devices target = /data
[ 2.917356] init: out of loopback devices system = jffs2
[ 2.924685] init: out of loopback devices options = (null)
[ 2.940149] [mmc]: sdc0 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 2.950606] init: command 'mount' r=0
[ 2.954858] init: processing action 0x1a0f010 (post-fs)
[ 2.961109] init: out of loopback devices source = rootfs
[ 2.967206] init: out of loopback devices target = /
[ 2.972933] init: out of loopback devices system = rootfs
[ 2.979024] init: out of loopback devices options = (null)
[ 2.985311] init: command 'mount' r=0
[ 2.989572] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 2.997949] init: processing action 0x1a0f070 (post-fs-data)
[ 3.004442] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 3.012907] [mmc]: sdc0 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.025301] init: command 'chown' r=0
[ 3.030611] [mmc]: sdc0 set ios: clk 200000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.041633] init: command 'chmod' r=0
[ 3.045859] init: command 'chmod' r=-2
[ 3.052560] init: command 'mkdir' r=0
[ 3.056748] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 8, RTO !!
[ 3.065026] *******************Try sdio*******************
[ 3.071724] init: command 'restorecon' r=0
[ 3.076378] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.085514] init: command 'mkdir' r=0
[ 3.089694] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.099699] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.108830] init: command 'mkdir' r=0
[ 3.113130] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.121390] *******************Try sd *******************
[ 3.128132] init: processing action 0x1a0fe20 (post-fs-data)
[ 3.134563] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.144656] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.154690] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.163675] init: skipping insecure file '/system/vendor/modules/videobuf-core.ko'
[ 3.172321] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.180682] *******************Try mmc*******************
[ 3.186863] [mmc]: sdc0 set ios: clk 200000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.200581] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 1, RTO !!
[ 3.209500] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.221089] [mmc]: sdc0 power_supply is null
[ 3.228683] [mmc]: sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.240152] [mmc]: sdc0 power_supply is null
[ 3.252619] init: command 'insmod' r=0
[ 3.257057] init: skipping insecure file '/system/vendor/modules/videobuf-dma-contig.ko'
[ 3.266347] [mmc]: sdc0 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.277644] init: command 'insmod' r=0
[ 3.282117] init: skipping insecure file '/system/vendor/modules/cci.ko'
[ 3.311167] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 3.320938] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 52, RTO !!
[ 3.329421] [mmc]: sdc0 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.345643] [VFE]cci probe start cci_sel = 0!
[ 3.351707] [mmc]: sdc0 set ios: clk 150000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.362123] [VFE]cci probe end cci_sel = 0!
[ 3.366946] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 3.375861] [VFE]cci_init end
[ 3.379385] init: command 'insmod' r=0
[ 3.385028] init: skipping insecure file '/system/vendor/modules/vfe_os.ko'
[ 3.393009] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 8, RTO !!
[ 3.401358] *******************Try sdio*******************
[ 3.407672] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 3.416482] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.425818] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.434418] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 3.443073] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.451463] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 3.460096] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5, RTO !!
[ 3.468416] *******************Try sd *******************
[ 3.475350] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 3.484004] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.492579] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 3.501113] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.510353] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 3.519351] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.528834] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 55, RTO !!
[ 3.537732] *******************Try mmc*******************
[ 3.543851] [mmc]: sdc0 set ios: clk 150000Hz bm OD pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.556236] [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 1, RTO !!
[ 3.565037] [mmc]: sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B
[ 3.576706] [mmc]: sdc0 power_supply is null
[ 3.604899] init: command 'insmod' r=0
[ 3.609334] init: skipping insecure file '/system/vendor/modules/vfe_subdev.ko'
[ 3.618672] init: command 'insmod' r=0
[ 3.623132] init: skipping insecure file '/system/vendor/modules/ar0330_mipi.ko'
[ 3.632629] init: command 'insmod' r=0
[ 3.637085] init: skipping insecure file '/system/vendor/modules/ov2710_mipi.ko'
[ 3.646622] init: command 'insmod' r=0
[ 3.651145] init: skipping insecure file '/system/vendor/modules/ov5647_mipi.ko'
[ 3.660722] init: command 'insmod' r=0
[ 3.665137] init: skipping insecure file '/system/vendor/modules/vfe_v4l2.ko'
[ 3.809531] [VFE]Welcome to Video Front End driver
[ 3.815648] [VFE]pdev->id = 0
[ 3.819046] [VFE]dev->mipi_sel = 0
[ 3.822953] [VFE]dev->vip_sel = 0
[ 3.826722] [VFE]dev->isp_sel = 0
[ 3.836737] [VFE_WARN]vfe vpu clock is null
[ 3.848052] [ISP] isp platform_id = 6!
[ 3.852510] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 3.861561] [VFE]probe_work_handle start!
[ 3.866109] [VFE]..........................vfe clk open!.......................
[ 3.874530] [VFE]vfe_init end
[ 3.878379] init: command 'insmod' r=0
[ 3.882846] init: skipping insecure file '/system/vendor/modules/uvcvideo.ko'
[ 3.891113] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 3.899770] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 3.908649] [VFE]v4l2 subdev register input_num = 0
[ 3.914277] [VFE]vfe sensor detect start! input_num = 0
[ 3.920189] [VFE]Find sensor name is "ov5647_mipi", i2c address is 6c, type is "RAW" !
[ 3.929164] [VFE]Sub device register "ov5647_mipi" i2c_addr = 0x6c start!
[ 3.936893] [VFE]v4l2_device_register_subdev return 0
[ 3.942631] [VFE]registered sensor subdev is OK!
[ 3.947849] [VFE]Check sensor!
[ 3.951425] [VFE]Sub device register "ov5647_mipi" is OK!
[ 3.960252] uvcvideo: Adding mapping Brightness to control 00000000-0000-0000-0000-000000000101/2.
[ 3.970560] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 3.979223] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[ 3.987762] uvcvideo: Adding mapping Contrast to control 00000000-0000-0000-0000-000000000101/3.
[ 3.997722] uvcvideo: Adding mapping Hue to control 00000000-0000-0000-0000-000000000101/6.
[ 4.007280] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[ 4.015999] uvcvideo: Adding mapping Saturation to control 00000000-0000-0000-0000-000000000101/7.
[ 4.026201] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[ 4.035003] uvcvideo: Adding mapping Sharpness to control 00000000-0000-0000-0000-000000000101/8.
[ 4.045932] uvcvideo: Adding mapping Gamma to control 00000000-0000-0000-0000-000000000101/9.
[ 4.055839] uvcvideo: Adding mapping Backlight Compensation to control 00000000-0000-0000-0000-000000000101/1.
[ 4.068131] [VFE]Check open /system/etc/hawkview/ov5647_mipi/isp_test_param.ini failed!
[ 4.068144] Match isp cfg start!
[ 4.081111] [VFE]Match isp cfg ok
[ 4.085057] uvcvideo: Adding mapping Gain to control 00000000-0000-0000-0000-000000000101/4.
[ 4.094578] uvcvideo: Adding mapping Power Line Frequency to control 00000000-0000-0000-0000-000000000101/5.
[ 4.106250] [VFE]V4L2 device registered as video0
[ 4.111769] [VFE]..........................vfe clk close!.......................
[ 4.120115] uvcvideo: Adding mapping Hue, Auto to control 00000000-0000-0000-0000-000000000101/16.
[ 4.130286] [VFE]probe_work_handle end!
[ 4.134743] uvcvideo: Adding mapping Exposure, Auto to control 00000000-0000-0000-0000-000000000001/2.
[ 4.145193] uvcvideo: Adding mapping Exposure, Auto Priority to control 00000000-0000-0000-0000-000000000001/3.
[ 4.156592] uvcvideo: Adding mapping Exposure (Absolute) to control 00000000-0000-0000-0000-000000000001/4.
[ 4.167595] uvcvideo: Adding mapping White Balance Temperature, Auto to control 00000000-0000-0000-0000-000000000101/11.
[ 4.179857] uvcvideo: Adding mapping White Balance Temperature to control 00000000-0000-0000-0000-000000000101/10.
[ 4.191544] uvcvideo: Adding mapping White Balance Component, Auto to control 00000000-0000-0000-0000-000000000101/13.
[ 4.203611] uvcvideo: Adding mapping White Balance Blue Component to control 00000000-0000-0000-0000-000000000101/12.
[ 4.215580] uvcvideo: Adding mapping White Balance Red Component to control 00000000-0000-0000-0000-000000000101/12.
[ 4.227456] uvcvideo: Adding mapping Focus (absolute) to control 00000000-0000-0000-0000-000000000001/6.
[ 4.238180] uvcvideo: Adding mapping Focus, Auto to control 00000000-0000-0000-0000-000000000001/8.
[ 4.248328] uvcvideo: Adding mapping Zoom, Absolute to control 00000000-0000-0000-0000-000000000001/11.
[ 4.258951] uvcvideo: Adding mapping Zoom, Continuous to control 00000000-0000-0000-0000-000000000001/12.
[ 4.269768] uvcvideo: Adding mapping Privacy to control 00000000-0000-0000-0000-000000000001/17.
[ 4.279888] usbcore: registered new interface driver uvcvideo
[ 4.286404] USB Video Class driver (v1.0.8_SONiX_v2.6.36.04)
[ 4.293127] init: command 'insmod' r=0
[ 4.297526] init: skipping insecure file '/system/vendor/modules/da380.ko'
[ 4.306597] step1 : gsensor_fetch_sysconfig_para
[ 4.311910] step2 : gsensor_fetch_sysconfig_para
[ 4.317243] step3 : gsensor_fetch_sysconfig_para
[ 4.322475] step4 : mir3da_init
[ 4.326275] i2c-core: driver [da380] using legacy suspend method
[ 4.333170] i2c-core: driver [da380] using legacy resume method
[ 4.339850] richard mir3da_detect: mir3da_detect:bus[0] addr[0x27]
[ 4.352262] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.366809] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.381253] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 4.390620] [MIR3DA] Can't find Mir3da gsensor!!
[ 4.395991] init: command 'insmod' r=0
[ 4.400435] init: skipping insecure file '/system/vendor/modules/sw-device.ko'
[ 4.412510] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 4.421997] init: command 'insmod' r=0
[ 4.426370] init: processing action 0x1a11420 (property_service_init)
[ 4.433770] init: skipping insecure file '/system/build.prop'
[ 4.440530] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 4.461354] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 4.489856] init: Created socket '/dev/socket/property_service' with mode '666', user '0', group '0'
[ 4.500488] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 4.509888] init: command 'property_service_init' r=0
[ 4.515652] init: processing action 0x1a11468 (signal_init)
[ 4.522196] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x18)
[ 4.531544] init: command 'signal_init' r=0
[ 4.536383] init: processing action 0x1a114b0 (check_startup)
[ 4.543022] init: command 'check_startup' r=0
[ 4.548057] init: processing action 0x1a0f1c8 (boot)
[ 4.553860] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 4.563678] init: command 'ifup' r=0
[ 4.567914] init: command 'hostname' r=0
[ 4.572480] init: command 'domainname' r=0
[ 4.577251] init: command 'setrlimit' r=0
[ 4.581994] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 4.591486] init: command 'chown' r=0
[ 4.595798] init: starting 'servicemanager'
[ 4.601168] init: starting 'vold'
[ 4.605413] init: starting 'media'
[ 4.609807] init: starting 'startupSound'
[ 4.614718] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 4.631235] init: Created socket '/dev/socket/vold' with mode '660', user '0', group '1009'
[ 4.649313] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 4.667347] init: command 'class_start' r=0
[ 4.681362] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x19)
[ 4.692618] init: starting 'ccdr'
[ 4.702616] init: command 'class_start' r=0
[ 4.715409] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 4.726150] init: processing action 0x1a0ffd0 (boot)
[ 4.732719] init: starting 'adbd'
[ 4.740654] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 4.752434] init: command 'start' r=0
[ 4.770641] init: Created socket '/dev/socket/adbd' with mode '660', user '1000', group '1000'
[ 4.784313] init: starting 'debuggerd'
[ 4.789036] init: command 'start' r=0
[ 4.795888] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 4.807548] init: starting 'standby'
[ 4.823261] init: command 'start' r=0
[ 4.827574] init: processing action 0x1a114f8 (queue_property_triggers)
[ 4.836627] adb_open
[ 4.844008] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 4.857882] init: command 'queue_property_triggers' r=0
[ 4.864659] init: processing action 0x1a0f4a8 (property:ro.debuggable=1)
[ 4.872460] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x8)
[ 4.884144] init: starting 'console'
[ 4.894143] init: command 'start' r=0
[ 4.900893] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.921803] init: processing action 0x1a10e10 (property:sys.usb.config=mass_storage,adb)
[ 4.931789] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.942837] android_usb: already disabled
[ 4.948134] init: command 'write' r=0
[ 4.955030] init: command 'write' r=0
[ 4.960287] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.971347] init: command 'write' r=0
[ 4.978733] init: command 'write' r=0
[ 4.983715] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 4.994656] ep_matches, wrn: endpoint already claimed, ep(0xc04d4fc4, 0xc1a75ac0, ep1in-bulk)
[ 5.004495] adb_bind_config
[ 5.007705] ep_matches, wrn: endpoint already claimed, ep(0xc04d4fc4, 0xc1a75ac0, ep1in-bulk)
[ 5.017383] ep_matches, wrn: endpoint already claimed, ep(0xc04d5010, 0xc1a75ac0, ep1out-bulk)
[ 5.027138] ep_matches, wrn: endpoint already claimed, ep(0xc04d4fc4, 0xc1a75ac0, ep1in-bulk)
[ 5.036708] ep_matches, wrn: endpoint already claimed, ep(0xc04d5010, 0xc1a75ac0, ep1out-bulk)
[ 5.046493] ep_matches, wrn: endpoint already claimed, ep(0xc04d505c, 0xc1a8ed40, ep2in-bulk)
[ 5.056824] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x38)
[ 5.066334] init: command 'write' r=0
[ 5.070645] init: command 'setprop' r=0
[ 5.080237] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 5.101319] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 5.130416] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 5.150905] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 5.190528] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x27)
[ 5.210249] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 5.230383] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 5.250494] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 5.271004] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 5.300767] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x26)
[ 5.330344] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 5.351170] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 5.381308] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 5.402347] android_usb gadget: high-speed config #1: android
[ 5.410542] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 5.441376] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1c)
[ 5.470238] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 5.491167] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 5.520514] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 5.540846] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 5.570518] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1d)
[ 5.602147] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 5.631533] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 5.660265] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 5.685267] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 5.710234] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x4c)
[ 5.730989] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.761008] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.793494] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.820818] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.850729] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x3d)
[ 5.880500] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.901235] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.930259] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 5.967582] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
root@camdroid:/ # [ 6.008157] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x28)
[ 6.031017] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 6.060611] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 6.090249] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 6.111328] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 6.140377] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x29)
[ 6.160323] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 6.181450] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 6.227776] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 6.281854] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 6.336295] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0xf)
[ 6.362814] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 6.391084] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 6.426783] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 6.468229] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 6.506542] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x15)
[ 6.530439] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.550410] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.570352] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.590588] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.610691] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1e)
[ 6.653228] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.683317] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.710736] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.740549] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 6.780981] sunxi_i2c_do_xfer()985 - [i2c0] incomplete xfer (status: 0x20, dev addr: 0x1f)
[ 7.529115] ▒newcdr▒▒▒▒: main entry
[ 7.534525] ▒newcdr▒▒▒▒: [Firmware Version: avr32@tiger_cdr 2022-07-18 17:24:40]
[ 7.552425] ▒newcdr▒▒▒▒: ===no need to check battery capacity ===
[ 7.577345] [VFE]vfe_open
[ 7.580854] [VFE]..........................vfe clk open!.......................
[ 7.589476] [VFE]vfe_open ok
[ 7.594820] [VFE]vfe_close
[ 7.598040] [VFE]vfe select input flag = 0, s_input have not be used .
[ 7.605432] [VFE]..........................vfe clk close!.......................
[ 7.613937] [VFE]vfe_close end
[ 7.617508] [VFE]vfe_open
[ 7.620560] [VFE]..........................vfe clk open!.......................
[ 7.629360] [VFE]vfe_open ok
[ 7.632821] [VFE]vfe_close
[ 7.636023] [VFE]vfe select input flag = 0, s_input have not be used .
[ 7.643395] [VFE]..........................vfe clk close!.......................
[ 7.652388] [VFE]vfe_close end
[ 8.629969] [DISP] ready enter pm_runtime_get_sync, device0
[ 8.798708] [VFE]vfe_open
[ 8.802428] [VFE]..........................vfe clk open!.......................
[ 8.811213] [VFE]vfe_open ok
[ 8.814958] [VFE]Set vfe core clk = 216000000, after Set vfe core clk = 297000000
[ 8.836205] [VFE]mclk on
[ 8.922671] [VFE]V4L2_MBUS_CSI2,2 lane,bus1 channel,rx 1 channel
[ 9.050467] [OV5647_mipi]s_fmt set width = 1280, height = 720
[ 9.087363] [VFE]width_input = 1280, height_input = 720, width = 1280, height = 720
[ 9.095994] [ISP] full_size width = 1280, height = 720.
[ 9.102002] [ISP] scale width = 480, height = 272
[ 9.107326] [VFE]dev->buf_byte_size = 1581056, double_ch_flag = 1
[ 9.114816] [ISP] VIDEO_MODE!
[ 9.179134] [VFE]buffer_setup, buffer count=5, size=1581056
[ 9.211316] ▒newcdr▒▒▒▒: startPreview finished
[ 9.251183] [VFE]capture video mode!
[ 9.284491] [VFE]capture video first frame done!
[ 9.449649] init: waitpid returned pid 67, status = 00000000
[ 9.463775] init: process 'startupSound', pid 67 exited
[ 9.777338] init: processing action 0x1a10e10 (property:sys.usb.config=mass_storage,adb)
[ 9.801380] adb_release
[ 9.805675] init: command 'write' r=0
[ 9.810257] adb_open
[ 9.821614] init: command 'write' r=0
[ 9.831191] init: command 'write' r=0
[ 9.836221] [VFE]vfe_open
[ 9.839282] [VFE_ERR]device open busy
[ 9.843501] [VFE]vfe_open busy
[ 9.847357] init: command 'write' r=0
[ 9.860878] ep_matches, wrn: endpoint already claimed, ep(0xc04d4fc4, 0xc1a75ac0, ep1in-bulk)
[ 9.880323] adb_bind_config
[ 9.883666] ep_matches, wrn: endpoint already claimed, ep(0xc04d4fc4, 0xc1a75ac0, ep1in-bulk)
[ 9.893327] ep_matches, wrn: endpoint already claimed, ep(0xc04d5010, 0xc1a75ac0, ep1out-bulk)
[ 9.903105] ep_matches, wrn: endpoint already claimed, ep(0xc04d4fc4, 0xc1a75ac0, ep1in-bulk)
[ 9.912765] ep_matches, wrn: endpoint already claimed, ep(0xc04d5010, 0xc1a75ac0, ep1out-bulk)
[ 9.922514] [VFE_WARN] Nobody is waiting on this video buffer,buf = 0xc0f03e40
[ 9.930659] ep_matches, wrn: endpoint already claimed, ep(0xc04d505c, 0xc1a8ed40, ep2in-bulk)
[ 9.950786] init: command 'write' r=0
[ 9.962757] init: command 'setprop' r=0
[ 10.222345] android_usb gadget: high-speed config #1: android
root@camdroid:/ #
root@camdroid:/ #
root@camdroid:/ #
/sys/class/disp/disp/attr/sys <
screen 0:
lcd output backlight(200) fps:62.1 800x 480
under_flow:0 skip:204 irq:3258
BUF enable ch[0] lyr[0] z[0] prem[N] a[pixel 128] fmt[ 77] fb[ 480, 272; 480, 272; 480, 272] crop[ 0, 0, 480, 272] frame[ 0, 0, 800, 480] addr[ 2b57000, 2b76e00, 110] flags[0x 0] trd[0,0]
BUF enable ch[2] lyr[0] z[11] prem[N] a[pixel 255] fmt[ 0] fb[ 800, 480; 800, 480; 800, 480] crop[ 0, 0, 800, 480] frame[ 0, 0, 800, 480] addr[42400000, 0, 0] flags[0x 0] trd[0,0]
acquire: 0, 25.5 fps
release: 0, 25.5 fps
display: 0, 25.5 fps
root@camdroid:/ #16M flash固件: 荔枝派旧板camdroid_16M_flash固件_20220719.7z
#4 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 我们家这台楼宇可视对讲视频一闪一闪, 其他功能正常, 还能抢救一下吗? » 2021-07-05 22:38:49
#5 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 我们家这台楼宇可视对讲视频一闪一闪, 其他功能正常, 还能抢救一下吗? » 2021-06-03 10:40:02
#6 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 我们家这台楼宇可视对讲视频一闪一闪, 其他功能正常, 还能抢救一下吗? » 2021-06-03 10:39:25
#7 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 这个十五年前的松下相机电池还能抢救一下吗? 放到冰箱-18℃里面冻了几天了。 » 2021-06-01 13:37:33
#8 DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 我们家这台楼宇可视对讲视频一闪一闪, 其他功能正常, 还能抢救一下吗? » 2021-06-01 11:31:18
#10 Re: VMWare/Linux/Ubuntu/Fedora/CentOS/U-BOOT » 我有一个windows应用程序在cygwin编译运行的, 请问怎么发布给客户呢? » 2021-05-21 10:57:00
#12 VMWare/Linux/Ubuntu/Fedora/CentOS/U-BOOT » 我有一个windows应用程序在cygwin编译运行的, 请问怎么发布给客户呢? » 2021-05-21 08:17:05
#13 Re: 全志 SOC » 全志官方melis系统在WIN7 WIN10中的环境搭建 » 2021-05-20 23:18:35
https://www.onelib.biz/blog/a/58291269b41431c00fbe4454
搞定了, 给所有 .exe 文件加执行属性:
find . |grep \.exe$ |xargs chmod 777
find . |grep \.dll$ |xargs chmod 777真是折腾够呛, 睡觉睡觉.
#14 Re: 全志 SOC » 全志官方melis系统在WIN7 WIN10中的环境搭建 » 2021-05-20 22:14:51
Creating archive 'elibs_ex.a'
cp elibs_ex.a ./../../../../libs/suniv/elibs_ex.a
rm elibs_ex.a
-------------------------------
lib ex build finish!
-------------------------------
make[4]: Leaving directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles/elibs/lib_ex'
make[3]: Leaving directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles/elibs'
make -C res
make[3]: Entering directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles/res'
make -C lang
make[4]: Entering directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles/res/lang'
./../../../../tools/build_tools/LangBuild/LangOSDBuild.exe ./lang.xml
make[4]: ./../../../../tools/build_tools/LangBuild/LangOSDBuild.exe: Permission denied
make[4]: *** [makefile:28: buildlang] Error 127
make[4]: Leaving directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles/res/lang'
make[3]: *** [makefile:28: buildres] Error 2
make[3]: Leaving directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles/res'
make[2]: *** [makefile:24: all] Error 2
make[2]: Leaving directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk/beetles'
make[1]: *** [makefile:23: all] Error 2
make[1]: Leaving directory '/cygdrive/d/C200S/melis2.0-sdk-release/livedesk'
make: *** [makefile:6: all] Error 2奇怪, 两台电脑都出现这个问题 LangOSDBuild.exe: Permission denied
#17 Re: 全志 SOC » 老人家，碰到新问题，mmcblk2变成了mmcblk1 » 2021-04-22 22:07:48
powerpan 说：
问题是uboot无法决定kernel怎么挂，挂成什么盘符，你说的貌似需要patch下kernel
https://lore.kernel.org/patchwork/cover/674381/
奔跑的孩子 说：这个问题我也纠结过，首先我改dts里面mmc别名，发现并没有什么卵用。
最好就是uboot脚本检测，然后生成不同的bootargs
对, 感觉 of_alias_get_id() 这个附近有bug
serial/uart 那些别名是没问题的
#18 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 闲鱼捡漏，拆解一台收银机【多图警告，流量党劝退】 » 2021-04-18 09:18:20
#20 Re: SigmaStar/SSD201/SSD202/SSD212 » SSD20x 开发从未入门到放弃 » 2021-02-28 17:38:03
那一堆pdf里面很多错别字和XJB乱拼的英语单词, 看得受不了.
RGB565的原理图不知道能不能参考这里面的资料:
感谢 深圳市启明云端科技 友情赠送的7寸电容 4G & WIFI SSD202 开发板
http://whycan.com/t_5891.html
#22 Re: SigmaStar/SSD201/SSD202/SSD212 » 有坛友玩SSD201的吗？ » 2021-02-11 16:20:55
/ # fbset
mode "1024x600-154"
# D: 124.425 MHz, H: 102.323 kHz, V: 153.638 Hz
geometry 1024 600 1024 600 32
timings 8037 64 64 32 32 64 2
accel false
rgba 8/16,8/8,8/0,8/24
endmode刚刚拿出启明吃灰的开发板试了一下,确实是 1024x600 的
dycbaba 说：
好像不是7寸1024*600 是800* 480 可能就5寸吧
九重天 说：算下来还好, 那个7寸1024*600 + GT911电容屏都要150元了.
dycbaba 说：这个价格还可以，450那个太贵了
#24 Re: 全志 SOC » 各侠大神，v3s BSP内核 如何测试音频驱动比如录音，播放声音？ » 2021-02-10 19:53:02
海豚派V3s开发板 camdroid 完整入坑记录
http://whycan.com/t_855.html
(出处:哇酷开发者社区)
看看一楼最底下?
#26 Re: 全志 SOC » 关于A40i linux SDK编译问题 » 2021-02-02 22:24:01
http://bbs.16rd.com/thread-478144-1-1.html
成功解决这个问题。 是内核配置文件没有配置好，只要用上对应全志的配置文件，然后重新编译，make ARCH=arm sunxi_defconfig 和在 make ARCH=arm menuconfig 上面配置好对应的架构和编译器， 然后再去编译 make -j8 源码 。就可以了。这个问题是很独特的和自己的内核配置文件相关性很大.
#27 Re: SigmaStar/SSD201/SSD202/SSD212 » 有没有人用过SigmaStar SSD201这颗芯片，感觉挺不错的啊 » 2021-01-25 21:46:06
dgp 说：
Sorry I don't know Chinese.
Basic SSD202 support will be in Linux 5.11:
USB, SD, SPI, I2C are already worked out. Display and audio are very difficult and we need some register descriptions...
U-boot is working too. There is some more work needed to make it boot from SPI NAND and to do the DDR setup on it's own so that the SigmaStar IPL binary is no longer needed.
https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/mstar-infinity2m-ssd202d.dtsi
https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/mstar-infinity2m-ssd20xd.dtsi
https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/mstar-infinity2m.dtsi
https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/mstar-infinity.dtsi
https://github.com/torvalds/linux/blob/master/arch/arm/boot/dts/mstar-v7.dtsi
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (c) 2020 thingy.jp.
* Author: Daniel Palmer <daniel@thingy.jp>
*/
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&gic>;
cpus: cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a7";
reg = <0x0>;
};
};
arch_timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2)
| IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2)
| IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2)
| IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2)
| IRQ_TYPE_LEVEL_LOW)>;
/*
* we shouldn't need this but the vendor
* u-boot is broken
*/
clock-frequency = <6000000>;
};
pmu: pmu {
compatible = "arm,cortex-a7-pmu";
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
interrupt-affinity = <&cpu0>;
};
soc: soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x16001000 0x16001000 0x00007000>,
<0x1f000000 0x1f000000 0x00400000>,
<0xa0000000 0xa0000000 0x20000>;
gic: interrupt-controller@16001000 {
compatible = "arm,cortex-a7-gic";
reg = <0x16001000 0x1000>,
<0x16002000 0x2000>,
<0x16004000 0x2000>,
<0x16006000 0x2000>;
#interrupt-cells = <3>;
interrupt-controller;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2)
| IRQ_TYPE_LEVEL_LOW)>;
};
riu: bus@1f000000 {
compatible = "simple-bus";
reg = <0x1f000000 0x00400000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x0 0x1f000000 0x00400000>;
pmsleep: syscon@1c00 {
compatible = "mstar,msc313-pmsleep", "syscon";
reg = <0x1c00 0x100>;
};
reboot {
compatible = "syscon-reboot";
regmap = <&pmsleep>;
offset = <0xb8>;
mask = <0x79>;
};
intc_fiq: interrupt-controller@201310 {
compatible = "mstar,mst-intc";
reg = <0x201310 0x40>;
#interrupt-cells = <3>;
interrupt-controller;
interrupt-parent = <&gic>;
mstar,irqs-map-range = <96 127>;
};
intc_irq: interrupt-controller@201350 {
compatible = "mstar,mst-intc";
reg = <0x201350 0x40>;
#interrupt-cells = <3>;
interrupt-controller;
interrupt-parent = <&gic>;
mstar,irqs-map-range = <32 95>;
mstar,intc-no-eoi;
};
l3bridge: l3bridge@204400 {
compatible = "mstar,l3bridge";
reg = <0x204400 0x200>;
};
gpio: gpio@207800 {
#gpio-cells = <2>;
reg = <0x207800 0x200>;
gpio-controller;
#interrupt-cells = <2>;
interrupt-controller;
interrupt-parent = <&intc_fiq>;
status = "disabled";
};
pm_uart: uart@221000 {
compatible = "ns16550a";
reg = <0x221000 0x100>;
reg-shift = <3>;
interrupts-extended = <&intc_irq GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
clock-frequency = <172000000>;
status = "disabled";
};
};
imi: sram@a0000000 {
compatible = "mmio-sram";
reg = <0xa0000000 0x10000>;
};
};
};瞄了一下设备树, 驱动的设备还不是很多.
#28 Re: 全志 SOC » [ESP8089-SPI移植支持设备树]F1C200S修改ESP8089源码，由原来板极描述文件改为设备树，一键配置。 » 2021-01-20 22:31:17
不错, 总算不要硬编码到代码里面了 ^_^
https://app6l6fnrf82978.h5.xiaoeknow.co … redirect=1
#29 Re: 全志 SOC » f1c100使用buildroot制作根文件系统出问题啦 » 2021-01-20 22:17:05
#30 Re: 计算机图形/GUI/RTOS/FileSystem/OpenGL/DirectX/SDL2 » 试一试 直接用 win32 api 运行 OpenGL 程序 » 2021-01-18 23:47:18
armstrong 说：
搬出我多年前的收藏给楼主助威吧，NEHE OpenGL 教学例程，例程个个精美：
nehegl.zip
不错, 找到官网了, 就是这个
https://github.com/gamedev-net/nehe-opengl/tree/master/vc
http://nehe.gamedev.net/tutorial/creating_an_opengl_window_(win32)/13001/
欢迎来到我的OpenGL教程。我是一个对OpenGL充满热情的普通人！当3Dfx为Voodoo 1卡发布他们的硬件加速OpenGL驱动程序时，我第一次听说OpenGL。我立刻知道OpenGL是我必须学习的东西。不幸的是，很难在书籍或网上找到有关OpenGL的任何信息。我花了数小时试图使代码正常工作，甚至花更多时间恳求人们在电子邮件和IRC上寻求帮助。我发现那些了解OpenGL的人认为自己是精英，对共享知识没有兴趣。非常令人沮丧！
看到这里, 感觉作者就像天使一样.
#31 Re: 全志 SOC » 不得不说, V3s的RTC就是渣渣, 电流10uA, 导致CR2032纽扣电池很快就放完电了, 不得不赶工改用PCF8563或者别的RTC » 2021-01-17 21:59:27
#32 Re: 全志 SOC » 我们这里玩V3S多，老外好像都玩的是A20 » 2021-01-10 13:15:16
#33 Re: Php/Nodejs/Web/HTML5/Javascript/微信开发/Python » 试一试 thinkphp 的 urlwrite 重写 » 2021-01-10 13:12:15
#35 VMWare/Linux/Ubuntu/Fedora/CentOS/U-BOOT » 可以在电脑ubuntu或者树莓派运行的无窗口OpenGL项目 » 2020-12-06 18:58:23
- 落日余晖
- 回复： 2
https://github.com/matusnovak/rpi-opengl-without-x
https://github.com/matusnovak/rpi-opengl-without-x/blob/master/triangle.c
ubuntu编译:
gcc -o triangle triangle.c -lEGL -lGL
运行:
./triangle
输出到 triangle.raw
#36 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 给大家推荐一个不错的多功能USB读卡器/转接器,还可以接上USB网卡，用手机有线上网哦 » 2019-11-23 18:38:42
#37 Re: DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 给大家推荐一个不错的多功能USB读卡器/转接器,还可以接上USB网卡，用手机有线上网哦 » 2019-11-23 18:37:26
#38 DIY/综合/Arduino/写字机/3D打印机/智能小车/平衡车/四轴飞行/MQTT/物联网 » 给大家推荐一个不错的多功能USB读卡器/转接器,还可以接上USB网卡，用手机有线上网哦 » 2019-11-23 18:34:50
页次： 1
- 首页
- » 搜索
- » 落日余晖 发表的帖子
感谢为中文互联网持续输出优质内容的各位老铁们。
QQ: 516333132, 微信(wechat): whycan_cn (哇酷网/挖坑网/填坑网) service@whycan.cn