WhyCan Forum(哇酷开发者社区)

感谢为中文互联网持续输出优质内容的各位老铁们。 QQ: 516333132, 微信(wechat): whycan_cn (哇酷网/挖坑网/填坑网) service@whycan.cn

您尚未登录。

#201 2019-05-15 11:22:58

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥,使用BSP内核,选通了ov5640。然后也更改了fex。

[csi1]                                                                          
vip_used                 = 1                                                    
vip_mode                 = 0                                                    
vip_dev_qty              = 1                                                    
vip_define_sensor_list   = 0                                                    
vip_csi_pck              = port:PE00<2><default><default><default>              
vip_csi_mck              = port:PE01<2><default><default><default>              
vip_csi_hsync            = port:PE02<2><default><default><default>              
vip_csi_vsync            = port:PE03<2><default><default><default>              
vip_csi_d0               = port:PE04<2><default><default><default>              
vip_csi_d1               = port:PE05<2><default><default><default>              
vip_csi_d2               = port:PE06<2><default><default><default>              
vip_csi_d3               = port:PE07<2><default><default><default>              
vip_csi_d4               = port:PE08<2><default><default><default>              
vip_csi_d5               = port:PE09<2><default><default><default>              
vip_csi_d6               = port:PE10<2><default><default><default>              
vip_csi_d7               = port:PE11<2><default><default><default>              
vip_csi_d8               = port:PE12<2><default><default><default>              
;vip_csi_d9               = port:PE13<2><default><default><default>             
vip_csi_d10               = port:PE14<2><default><default><default>             
vip_csi_d11               = port:PE15<2><default><default><default>             
                                                                                
vip_csi_sck               = port:PE21<2><default><default><default>             
vip_csi_sda               = port:PE22<2><default><default><default>             
                                                                                
vip_dev0_mname           = "ov5640"                                             
vip_dev0_pos             = "front"                                              
vip_dev0_twi_id          = 4                                                    
vip_dev0_twi_addr        = 0x78                                                 
vip_dev0_isp_used        = 0                                                    
vip_dev0_fmt             = 0                                                    
vip_dev0_stby_mode       = 0                                                    
vip_dev0_vflip           = 0                                                    
vip_dev0_hflip           = 0                                                    
vip_dev0_iovdd           = ""                                                   
vip_dev0_iovdd_vol       = 2800000                                              
vip_dev0_avdd            = ""                                                   
vip_dev0_avdd_vol        = 2800000                                              
vip_dev0_dvdd            = ""                                                   
vip_dev0_dvdd_vol        = 1500000                                              
vip_dev0_afvdd           = ""                                                   
vip_dev0_afvdd_vol       = 2800000                                              
vip_dev0_power_en        =                                                      
vip_dev0_reset           = port:PE23<1><default><default><default>
vip_dev0_pwdn            = port:PE24<1><default><default><default>              
vip_dev0_flash_en        =                                                      
vip_dev0_flash_mode      =                                                      
vip_dev0_af_pwdn         =                                                      
                                                                                
vip_dev0_act_used        = 0                                                    
vip_dev0_act_name        = "ad5820_act"                                         
vip_dev0_act_slave       = 0x18                                                 
                                                                                
vip_dev1_mname           = "gc2035"                                             
vip_dev1_pos                 = "front"                                          
vip_dev1_lane            = 1                                                    
vip_dev1_twi_id          = 4                                                    
vip_dev1_twi_addr        = 0x78                                                 
vip_dev1_isp_used        = 0                                                    
vip_dev1_fmt             = 1                                                    
vip_dev1_stby_mode       = 0                                                    
vip_dev1_vflip           = 0                                                    
vip_dev1_hflip           = 0                                                    
vip_dev1_iovdd           = ""                                                   
vip_dev1_iovdd_vol       = 2800000                                              
vip_dev1_avdd            = ""                                                   
vip_dev1_avdd_vol        = 2800000                                              
vip_dev1_dvdd            = ""                                                   
vip_dev1_dvdd_vol        = 1500000                                              
vip_dev1_afvdd           = ""                                                   
vip_dev1_afvdd_vol       = 2800000                                              
vip_dev1_power_en        =                                                      
vip_dev1_reset           =                                                      
vip_dev1_pwdn            =                                                      
vip_dev1_flash_en        =                                                      
vip_dev1_flash_mode      =                                                      
vip_dev1_af_pwdn         = 

可是在用fswebcam拍照时

# fswebcam -S 10 -d /dev/video1 -p YUV420P -r 640x480 test21.jpg
[   26.003939] [VFE]vfe_open
--- Opening /dev/video1...
[   26.007092] [VFE]..........................vfe clk open!.......................
Trying source module v4l2...[   26.018941] [VFE]vfe_open ok

/dev/video1 opened.
[   26.024950] [VFE_ERR]input index(0) > dev->dev_qty(1)-1 invalid!, device_valid_flag[0] = 0
No input was specified, usin[   26.037247] [VFE]vfe_close
g the first.
Unable to[   26.042806] [VFE]vfe select input flag = 0, s_input have not be used .
 query input 0.
VIDIOC[   26.053040] [VFE]..........................vfe clk close!.......................
_ENUMINPUT: Invalid argument
   26.064499] [VFE]vfe_close end
0m# 
# 
# 
# 
# 
# 
# 
# 
# i2cd
i2cdetect  i2cdump
# i2cd
i2cdetect  i2cdump
# i2cdetect -l
i2cdetect: can't open '/sys/class/i2c-dev': No such file or directory
# i2cdetect -y 1
i2cdetect: can't open '/dev/i2c/1': No such file or directory
# ls
# 

这是什么原因呢

离线

#202 2019-05-15 11:33:22

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

有没有 /dev/i2cX,   /dev/i2c/X 这些设备, 如果没有可能是 menuconfig 上面没有勾选 I2C User Interface

离线

#203 2019-05-15 11:40:59

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

有没有 /dev/i2cX,   /dev/i2c/X 这些设备, 如果没有可能是 menuconfig 上面没有勾选 I2C User Interface


主要是这个错误

--- Opening /dev/video1...
[   33.650171] [VFE]vfe_open
Trying source module v4l2...[   33.656150] [VFE]..........................vfe clk open!.......................

[   33.667840] [VFE]vfe_open ok
[   33.671467] [VFE_ERR]input index(0) > dev->dev_qty(1)-1 invalid!, device_valid_flag[0] = 0
/dev/video1 opened.
No [   33.681675] [VFE]vfe_close
input was specified, using the f[   33.686958] [VFE]vfe select input flag = 0, s_input have not be used .
irst.
Unable to query [   33.697235] [VFE]..........................vfe clk close!.......................
input 0.
VIDIOC_ENUMIN[   33.708530] [VFE]vfe_close end
PUT: Invalid argument

不知道这个是什么造成的

最近编辑记录 晕哥小弟 (2019-05-15 11:41:19)

离线

#204 2019-05-15 11:42:03

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

https://www.kancloud.cn/lichee/lpi0/470832
群主也有这个问题,但是没有说清楚。

离线

#205 2019-05-15 11:43:09

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Linux version 3.4.39 (he@he) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-29) ) #37 Wed May 15 11:39:13 CST 2019
[    0.000000] Initialized persistent memory from 41d20800-41d307ff
[    0.000000] Kernel command line: console=ttyS0,115200 panic=5 rootwait root=/dev/mmcblk0p2 earlyprintk rw
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 64MB = 64MB total
[    0.000000] Memory: 29176k/29176k available, 36360k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc4800000 - 0xff000000   ( 936 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc052b000   (5260 kB)
[    0.000000]       .init : 0xc052b000 - 0xc054f000   ( 144 kB)
[    0.000000]       .data : 0xc0550000 - 0xc05cd490   ( 502 kB)
[    0.000000]        .bss : 0xc05cd4b4 - 0xc06ae354   ( 900 kB)
[    0.000000] NR_IRQS:544
[    0.000000] Architected local timer running at 24.00MHz.
[    0.000000] Switching to timer-based delay loop
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[    0.000000] Console: colour dummy device 80x30
[    0.000148] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000)
[    0.000168] pid_max: default: 32768 minimum: 301
[    0.000312] Mount-cache hash table entries: 512
[    0.000870] CPU: Testing write buffer coherency: ok
[    0.001132] Setting up static identity map for 0x403aa208 - 0x403aa260
[    0.001816] devtmpfs: initialized
[    0.003522] pinctrl core: initialized pinctrl subsystem
[    0.004012] NET: Registered protocol family 16
[    0.004320] DMA: preallocated 128 KiB pool for atomic coherent allocations
[    0.004380] script_sysfs_init success
[    0.005154] gpiochip_add: registered GPIOs 0 to 223 on device: sunxi-pinctrl
[    0.006059] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver
[    0.006427] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl
[    0.007202] persistent_ram: found existing buffer, size 21180, start 21180
[    0.101129] console [ram-1] enabled
[    0.102061] Not Found clk pll_isp in script 
[    0.102194] Not Found clk pll_video in script 
[    0.102422] Not Found clk pll_ve in script 
[    0.102544] Not Found clk pll_periph0 in script 
[    0.102665] Not Found clk pll_de in script 
[    0.107130] bio: create slab <bio-0> at 0
[    0.107512] pwm module init!
[    0.109723] SCSI subsystem initialized
[    0.110225] usbcore: registered new interface driver usbfs
[    0.110433] usbcore: registered new interface driver hub
[    0.110801] usbcore: registered new device driver usb
[    0.111097] twi_chan_cfg()340 - [twi0] has no twi_regulator.
[    0.111227] twi_chan_cfg()340 - [twi1] has no twi_regulator.
[    0.111456] Linux video capture interface: v2.00
[    0.111650] gpiochip_add: gpios 1024..1028 (axp_pin) failed to register
[    0.112215] Advanced Linux Sound Architecture Driver Version 1.0.25.
[    0.113108] Switching to clocksource arch_sys_counter
[    0.119984] NET: Registered protocol family 2
[    0.119984] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.119984] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.119984] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.119984] TCP: Hash tables configured (established 2048 bind 2048)
[    0.120225] TCP: reno registered
[    0.120355] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.120593] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.120985] NET: Registered protocol family 1
[    0.121452] standby_mode = 1. 
[    0.121680] wakeup src cnt is : 3. 
[    0.121820] pmu1_enable = 0x1. 
[    0.121940] pmux_id = 0x1. 
[    0.122172] config_pmux_para: script_parser_fetch err. 
[    0.122296] pmu2_enable = 0x0. 
[    0.122423] add_sys_pwr_dm: get ldo name failed
[    0.122651] add_sys_pwr_dm: get ldo name failed
[    0.122774] add_sys_pwr_dm: get ldo name failed
[    0.122897] add_sys_pwr_dm: get ldo name failed
[    0.123125] add_sys_pwr_dm: get ldo name failed
[    0.123248] add_sys_pwr_dm: get ldo name failed
[    0.123474] add_sys_pwr_dm: get ldo name failed
[    0.123598] add_sys_pwr_dm: get ldo name failed
[    0.123720] add_sys_pwr_dm: get ldo name failed
[    0.123947] add_sys_pwr_dm: get ldo name failed
[    0.124068] after inited: sys_mask config = 0x0. 
[    0.124291] dynamic_standby enalbe = 0x0. 
[    0.124462] sunxi_reg_init enter
[    0.126525] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.126818] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.127135] msgmni has been set to 56
[    0.128317] io scheduler noop registered
[    0.128454] io scheduler deadline registered
[    0.128654] io scheduler cfq registered (default)
[    0.129271] [DISP]disp_module_init
[    0.129786] cmdline,disp=
[    0.130184] [DISP] disp_get_rotation_sw,line:68:disp 0 out of range? g_rot_sw=0
[    0.130534] [DISP] disp_init_connections,line:289:NULL pointer: 0, 0
[    0.131503] [DISP] lcd_clk_config,line:886:disp 0, clk: pll(0),clk(0),dclk(0) dsi_rate(0)
[    0.132966] [DISP]disp_module_init finish
[    0.133477] sw_uart_get_devinfo()1503 - uart0 has no uart_regulator.
[    0.133936] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI
[    0.134173] sw_uart_pm()890 - uart0 clk is already enable
[    0.134307] sw_console_setup()1233 - console setup baud 115200 parity n bits 8, flow n
[    0.247778] console [ttyS0] enabled
[    0.737814] sunxi_spi_chan_cfg()1376 - [spi-0] has no spi_regulator.
[    0.745700] spi spi0: master is unqueued, this is deprecated
[    0.753808] Failed to alloc md5
[    0.757463] eth0: Use random mac address
[    0.762122] usbcore: registered new interface driver catc
[    0.768378] usbcore: registered new interface driver kaweth
[    0.774700] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[    0.783272] usbcore: registered new interface driver pegasus
[    0.789803] usbcore: registered new interface driver rtl8150
[    0.796290] usbcore: registered new interface driver asix
[    0.802556] usbcore: registered new interface driver cdc_ether
[    0.809180] usbcore: registered new interface driver cdc_eem
[    0.815721] usbcore: registered new interface driver dm9601
[    0.822081] usbcore: registered new interface driver smsc75xx
[    0.828731] usbcore: registered new interface driver smsc95xx
[    0.835257] [DISP] disp_lcd_pwm_enable,line:1021:pwm device hdl is NULL
[    0.843015] usbcore: registered new interface driver gl620a
[    0.849351] usbcore: registered new interface driver net1080
[    0.855901] usbcore: registered new interface driver plusb
[    0.862163] usbcore: registered new interface driver rndis_host
[    0.868983] usbcore: registered new interface driver cdc_subset
[    0.875716] usbcore: registered new interface driver zaurus
[    0.882171] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[    0.890577] usbcore: registered new interface driver int51x1
[    0.897114] usbcore: registered new interface driver kalmia
[    0.903471] usbcore: registered new interface driver ipheth
[    0.909918] usbcore: registered new interface driver sierra_net
[    0.916652] usbcore: registered new interface driver cx82310_eth
[    0.923594] usbcore: registered new interface driver cdc_ncm
[    0.930052] usbcore: registered new interface driver lg-vl600
[    0.936686] usbcore: registered new interface driver qmi_wwan
[    0.943549] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.971131] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.980494] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1
[    0.989127] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000
[    1.010037] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00
[    1.016821] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.024598] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.032841] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.041277] usb usb1: Manufacturer: Linux 3.4.39 ehci_hcd
[    1.047482] usb usb1: SerialNumber: sunxi-ehci
[    1.053225] hub 1-0:1.0: USB hub found
[    1.057525] hub 1-0:1.0: 1 port detected
[    1.062594] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.089650] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.098627] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 2
[    1.107320] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400
[    1.174098] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.181867] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.189997] usb usb2: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    1.198140] usb usb2: Manufacturer: Linux 3.4.39 ohci_hcd
[    1.204353] usb usb2: SerialNumber: sunxi-ohci
[    1.209963] hub 2-0:1.0: USB hub found
[    1.214293] hub 2-0:1.0: 1 port detected
[    1.219417] usbcore: registered new interface driver cdc_acm
[    1.225859] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.235026] usbcore: registered new interface driver cdc_wdm
[    1.241433] Initializing USB Mass Storage driver...
[    1.247153] usbcore: registered new interface driver usb-storage
[    1.253944] USB Mass Storage support registered.
[    1.259413] usbcore: registered new interface driver usbserial
[    1.266023] usbserial: USB Serial Driver core
[    1.271140] usbcore: registered new interface driver option
[    1.277468] USB Serial support registered for GSM modem (1-port)
[    1.284447] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    1.291574] sunxikbd_script_init: key para not found, used default para. 
[    1.300339] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0
[    1.307857] i2c /dev entries driver
[    1.312242] [VFE]cci probe start cci_sel = 0!
[    1.317218] [VFE]cci probe end cci_sel = 0!
[    1.322029] [VFE]cci_init end
[    1.325551] [VFE]Welcome to Video Front End driver
[    1.331245] [VFE]pdev->id = 1
[    1.334651] [VFE]dev->mipi_sel = 1
[    1.338637] [VFE]dev->vip_sel = 1
[    1.342448] [VFE]dev->isp_sel = 0
[    1.352354] [VFE_WARN]vfe vpu clock is null
[    1.357517] [VFE_ERR]vip1 request pinctrl handle for device [csi1] failed!
[    1.365478] [VFE]vfe_init end
[    1.369790] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[    1.378681] [VFE]probe_work_handle start!
[    1.383365] [VFE]..........................vfe clk open!.......................
[    1.391748] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[    1.400719] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[    1.409444] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[    1.418282] [VFE]v4l2 subdev register input_num = 0
[    1.423928] [VFE]vfe sensor detect start! input_num = 0
[    1.429842] [VFE]Find sensor name is "ov5640", i2c address is 78, type is "YUV" !
[    1.438371] [VFE]Sub device register "ov5640" i2c_addr = 0x78 start!
[    1.445540] [VFE_ERR]Error registering v4l2 subdevice No such device!
[    1.452910] [VFE_ERR]vfe sensor register check error at input_num = 0
[    1.460313] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[    1.469051] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[    1.477814] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[    1.487041] [VFE]V4L2 device registered as video1
[    1.492418] sunxi_wdt_init_module: sunxi WatchDog Timer Driver v1.0
[    1.499681] sunxi_wdt_probe: devm_ioremap return wdt_reg 0xf1c20ca0, res->start 0x01c20ca0, res->end 0x01c20cbf
[    1.510965] [VFE]..........................vfe clk close!.......................
[    1.519711] [VFE]probe_work_handle end!
[    1.524273] sunxi_wdt_probe: initialized (g_timeout=16s, g_nowayout=0)
[    1.531757] wdt_enable, write reg 0xf1c20cb8 val 0x00000000
[    1.538056] wdt_set_tmout, write 0x000000b0 to mode reg 0xf1c20cb8, actual timeout 16 sec
[    1.549954] sunxi_leds_fetch_sysconfig_para leds is not used in config
[    1.557480] =========script_get_err============
[    1.564103] usbcore: registered new interface driver usbhid
[    1.570538] usbhid: USB HID core driver
[    1.575561] ashmem: initialized
[    1.579298] logger: created 256K log 'log_main'
[    1.584942] logger: created 32K log 'log_events'
[    1.590357] logger: created 32K log 'log_radio'
[    1.595636] logger: created 32K log 'log_system'
[    1.606895] asoc: sndcodec <-> sunxi-codec mapping ok
[    1.612686] *******************Try sdio*******************
[    1.621126] TCP: cubic registered
[    1.625001] NET: Registered protocol family 17
[    1.630254] VFP support v0.3: [mmc]: *** sunxi_mci_dump_errinfo(L826): smc 0 err, cmd 5,  RTO !!
[    1.640507] ThumbEE CPU extension supported.
[    1.645483] *******************Try sd *******************
[    1.651613] Registering SWP/SWPB emulation handler
[    1.658081] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[    1.667140] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[    1.677168] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[    1.688018] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[    1.696613] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[    1.705301] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[    1.714174] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[    1.722981] sunxi-rtc sunxi-rtc: setting system clock to 1970-01-01 00:00:10 UTC (10)
[    1.733372] ALSA device list:
[    1.736805]   #0: audiocodec
[    1.740542] Waiting for root device /dev/mmcblk0p2...
[    1.777498] mmc0: new high speed SDHC card at address aaaa
[    1.784150] mmcblk0: mmc0:aaaa SC16G 14.8 GiB 
[    1.793829]  mmcblk0: p1 p2
[    1.797839] mmcblk mmc0:aaaa: Card claimed for testing.
[    1.803921] mmc0:aaaa: SC16G 14.8 GiB 
[    1.808312] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[    1.817174] *******************sd init ok*******************
[    1.823657] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[    1.832519] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[    1.841079] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[    1.849727] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[    1.858414] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[    1.866975] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[    1.962903] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.974732] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    2.020978] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    2.030169] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    2.041157] devtmpfs: mounted
[    2.044757] Freeing init memory: 144K
[    2.163985] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
Starting syslogd: OK
Starting klogd: OK
Initializing random number generator... done.
Starting network: OK

Welcome to Buildroot
buildroot login: root
# 
# 
# 
# 
# i2cdetect -y
BusyBox v1.29.3 (2019-04-29 11:17:35 CST) multi-call binary.

Usage: i2cdetect -l | -F I2CBUS | [-ya] [-q|-r] I2CBUS [FIRST LAST]

Detect I2C chips

        -l      List installed buses
        -F BUS# List functionalities on this bus
        -y      Disable interactive mode
        -a      Force scanning of non-regular addresses
        -q      Use smbus quick write commands for probing (default)
        -r      Use smbus read byte commands for probing
        FIRST and LAST limit probing range
# i2cdetect -l
# fswebcam -S 10 -d /dev/video1 -p YUV420P -r 640x480 test21.jpg
--- Opening /dev/video1...
[   33.650171] [VFE]vfe_open
Trying source module v4l2...[   33.656150] [VFE]..........................vfe clk open!.......................

[   33.667840] [VFE]vfe_open ok
[   33.671467] [VFE_ERR]input index(0) > dev->dev_qty(1)-1 invalid!, device_valid_flag[0] = 0
/dev/video1 opened.
No [   33.681675] [VFE]vfe_close
input was specified, using the f[   33.686958] [VFE]vfe select input flag = 0, s_input have not be used .
irst.
Unable to query [   33.697235] [VFE]..........................vfe clk close!.......................
input 0.
VIDIOC_ENUMIN[   33.708530] [VFE]vfe_close end
PUT: Invalid argument
# 
# 
# 
# 
# 
#

附上我的启动信息。有时间帮我分析原因。

离线

#206 2019-05-15 13:44:08

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

看前面的错误, 觉得应该是 没有生成 /dev/videoX 设备,

看log 果然是视频设备没有注册成功:

[    1.418282] [VFE]v4l2 subdev register input_num = 0
[    1.423928] [VFE]vfe sensor detect start! input_num = 0
[    1.429842] [VFE]Find sensor name is "ov5640", i2c address is 78, type is "YUV" !
[    1.438371] [VFE]Sub device register "ov5640" i2c_addr = 0x78 start!
[    1.445540] [VFE_ERR]Error registering v4l2 subdevice No such device!
[    1.452910] [VFE_ERR]vfe sensor register check error at input_num = 0

menuconfig 里面有 ov5640 吗? ov5640 与 ov5647 的设备Id 不同的。

离线

#207 2019-05-15 13:46:25

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

不对吧,你往下看,产生了 /dev/video1啊

离线

#208 2019-05-15 14:19:19

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:

不对吧,你往下看,产生了 /dev/video1啊

嗯, 眼花了。

找到这个, 问题和你的一样,
https://licheezero.readthedocs.io/zh/latest/系统开发/bsp_cam.html

但是我仍然没看出来他是如何解决的.

离线

#209 2019-05-15 14:29:25

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

这就咋玩了,主线生成不了/dev/video*  BSP 虽然生成了/dev/video1但是拍照会发生上面的错误。。。。。。

离线

#210 2019-05-15 14:32:49

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:

这就咋玩了,主线生成不了/dev/video*  BSP 虽然生成了/dev/video1但是拍照会发生上面的错误。。。。。。

有没有试过这个: https://whycan.cn/t_1780.html

离线

#211 2019-05-15 14:35:41

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:
晕哥小弟 说:

这就咋玩了,主线生成不了/dev/video*  BSP 虽然生成了/dev/video1但是拍照会发生上面的错误。。。。。。

有没有试过这个: https://whycan.cn/t_1780.html


我这边是得到的消息是 ov5647停产了。而且市面上不好购买。另外我用fswebcam拍照的话,10次大概有1-2次拍照出来是个空照片。

离线

#212 2019-05-15 15:05:07

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:
晕哥 说:
晕哥小弟 说:

这就咋玩了,主线生成不了/dev/video*  BSP 虽然生成了/dev/video1但是拍照会发生上面的错误。。。。。。

有没有试过这个: https://whycan.cn/t_1780.html


我这边是得到的消息是 ov5647停产了。而且市面上不好购买。另外我用fswebcam拍照的话,10次大概有1-2次拍照出来是个空照片。

用上面的固件, 会有空照片?

离线

#213 2019-05-15 15:39:58

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:
晕哥小弟 说:
晕哥 说:

有没有试过这个: https://whycan.cn/t_1780.html


我这边是得到的消息是 ov5647停产了。而且市面上不好购买。另外我用fswebcam拍照的话,10次大概有1-2次拍照出来是个空照片。

用上面的固件, 会有空照片?

是的,我之前测试的时候发现的,好像拍了十几张的样子,然后有一张图片生成了,但是就是没有图像。后来我就没有管了。换linux了。

离线

#214 2019-05-15 18:57:05

lgliang
会员
注册时间: 2019-04-26
累计积分: 11

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

Jmhh247 说:
晕哥 说:

先用 bmp 文件测试, 如果 bmp 文件都正常, 说明缺 png 库.

那可能 buildroot 没有勾上 libpng,
也可能勾上了 libpng,
但是你的 Qt 路径, plugins 子目录下面没有 png 插件,
缺一不可.

折腾了两天,终于能显示png了。。。

确实在buildroot里面勾上 png相关支持就可以了,然后要删除掉qt5目录内的.stamp_built .stamp_configured 。

刚开始我没删掉这些,生成的根文件系统还是不支持显示png

感觉自己蠢哭了。。。


我也遇到了这个问题,请问是删除掉“./buildroot-2017.08.1/output/build/qt5base-5.9.1/.stamp_built”,和 “./buildroot-2017.08.1/output/build/qt5base-5.9.1/.stamp_configured” 这两个目录下的文件么,请指教!!

离线

#215 2019-05-15 20:22:44

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

可以先这样试一试

离线

#216 2019-05-15 22:36:06

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥,有方法可以把主线的uboot.bin   +  bsp kernel  + script.bin 等等打包一个img文件,我烧到flash中,之前好像在论坛里面看到。今天早了很长时间没有找到。

离线

#217 2019-05-16 08:08:45

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:

晕哥,有方法可以把主线的uboot.bin   +  bsp kernel  + script.bin 等等打包一个img文件,我烧到flash中,之前好像在论坛里面看到。今天早了很长时间没有找到。

https://whycan.cn/t_682.html (licheepi zero BSP 内核(linux3.4) 编译教程)

离线

#218 2019-05-16 08:38:46

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥,上面你提供的链接,我搜到了,我现在的环境是主线u-boot + BSP 内核。想烧写到spi-flash中。

离线

#219 2019-05-16 08:46:58

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:

晕哥,上面你提供的链接,我搜到了,我现在的环境是主线u-boot + BSP 内核。想烧写到spi-flash中。

可以的, 貌似我以前做过 flash 固件, 刚刚没找到。

离线

#220 2019-05-16 08:51:54

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

我其实不需要固件,我需要个步骤。 因为现在我有主线的uboot  BSPkernel +  boot.scr  + script.bin +还有一个rootfs (我不知道是什么格式,是buildroot生成的) 这些我不知道烧写到什么位置。

离线

#221 2019-05-16 10:27:41

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥,按照自己的理解,和参照网上。自己折腾了下。
https://whycan.cn/t_682.html (licheepi zero BSP 内核(linux3.4) 编译教程)
21、启动不起来,任何串口任何信息都没有。

最近编辑记录 晕哥小弟 (2019-05-16 11:46:59)

离线

#222 2019-05-16 10:48:33

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

串口连 u-boot 信息都没有?

到这里跟帖吧:
https://whycan.cn/t_682.html (licheepi zero BSP 内核(linux3.4) 编译教程)

离线

#223 2019-05-17 16:09:25

jianke512
会员
注册时间: 2019-05-17
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥,现在调试LecheePi Zero,屏幕800x480,已按照1楼的配置更改UBOOT,kernel用的800x480的dtb,启动过程中UBOOT屏幕可以显示,linux kernel屏幕不显示并且kernel hang住,请帮忙给些调试建议

kernle停在Console: switching to colour dummy device 80x30位置不动了



U-Boot SPL 2017.01-rc2 (May 17 2019 - 15:06:54)                                 
DRAM: 64 MiB                                                                    
Trying to boot from MMC1                                                        
                                                                                
U-Boot 2017.01-rc2 (May 17 2019 - 15:06:54 +0800) Allwinner Technology          
                                                                                
CPU:   Allwinner V3s (SUN8I 1681)                                               
Model: Lichee Pi Zero                                                           
DRAM:  64 MiB                                                                   
MMC:   SUNXI SD/MMC: 0                                                          
*** Warning - bad CRC, using default environment                                
                                                                                
Setting up a 800x480 lcd console (overscan 0x0)                                 
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6                              
In:    serial@01c28000                                                          
Out:   serial@01c28000                                                          
Err:   serial@01c28000                                                          
                                                                                
                                                                                
U-Boot 2017.01-rc2 (May 17 2019 - 15:06:54 +0800) Allwinner Technology          
                                                                                
CPU:   Allwinner V3s (SUN8I 1681)                                               
Model: Lichee Pi Zero                                                           
DRAM:  64 MiB                                                                   
MMC:   SUNXI SD/MMC: 0                                                          
*** Warning - bad CRC, using default environment                                
                                                                                
Setting up a 800x480 lcd console (overscan 0x0)                                 
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6                              
In:    serial@01c28000                                                          
Out:   serial@01c28000                                                          
Err:   serial@01c28000                                                          
Net:   No ethernet found.                                                       
starting USB...                                                                 
No controllers found                                                            
Hit any key to stop autoboot:  0                                                
reading zImage                                                                  
4021504 bytes read in 218 ms (17.6 MiB/s)                                       
reading sun8i-v3s-licheepi-zero-with-800x480-lcd.dtb                            
11953 bytes read in 27 ms (431.6 KiB/s)                                         
## Flattened Device Tree blob at 41800000                                       
   Booting using the fdt blob at 0x41800000                                     
   Loading Device Tree to 42dfa000, end 42dffeb0 ... OK                         
                                                                                
Starting kernel ...                                                             
                                                                                
[    0.000000] Booting Linux on physical CPU 0x0                                
[    0.000000] Linux version 4.14.14-licheepi-zero (root@muwei) (gcc version 7.9
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d  
[    0.000000] CPU: div instructions available: patching division code          
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructie
[    0.000000] OF: fdt: Machine model: Lichee Pi Zero                           
[    0.000000] Memory policy: Data cache writealloc                             
[    0.000000] random: fast init done                                           
[    0.000000] percpu: Embedded 16 pages/cpu @c3de6000 s33740 r8192 d23604 u6556
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 15883     
[    0.000000] Kernel command line: console=ttyS0,115200 rootwait root=/dev/mmcw
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)              
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)    
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)     
[    0.000000] Memory: 53512K/64036K available (6144K kernel code, 284K rwdata,)
[    0.000000] Virtual kernel memory layout:                                    
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)                
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)                
[    0.000000]     vmalloc : 0xc4000000 - 0xff800000   ( 952 MB)                
[    0.000000]     lowmem  : 0xc0000000 - 0xc3e89000   (  62 MB)                
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)                
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)                
[    0.000000]       .text : 0xc0008000 - 0xc0700000   (7136 kB)                
[    0.000000]       .init : 0xc0900000 - 0xc0a00000   (1024 kB)                
[    0.000000]       .data : 0xc0a00000 - 0xc0a473a0   ( 285 kB)                
[    0.000000]        .bss : 0xc0a4e6dc - 0xc0a902e4   ( 264 kB)                
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1       
[    0.000000] Hierarchical RCU implementation.                                 
[    0.000000]  RCU event tracing is enabled.                                   
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.            
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1     
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16                  
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).            
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398s
[    0.000018] Switching to timer-based delay loop, resolution 41ns             
[    0.000179] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, maxs
[    0.000430] Console: colour dummy device 80x30                               
[    0.000470] Calibrating delay loop (skipped), value calculated using timer f)
[    0.000486] pid_max: default: 32768 minimum: 301                             
[    0.000612] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)      
[    0.000627] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 
[    0.001273] CPU: Testing write buffer coherency: ok                          
[    0.001665] /cpus/cpu@0 missing clock-frequency property                     
[    0.001692] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000                 
[    0.002158] Setting up static identity map for 0x40100000 - 0x40100060       
[    0.002338] Hierarchical SRCU implementation.                                
[    0.002846] smp: Bringing up secondary CPUs ...                              
[    0.002860] smp: Brought up 1 node, 1 CPU                                    
[    0.002868] SMP: Total of 1 processors activated (48.00 BogoMIPS).           
[    0.002876] CPU: All CPU(s) started in SVC mode.                             
[    0.003681] devtmpfs: initialized                                            
[    0.006874] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5
[    0.007170] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[    0.007198] futex hash table entries: 256 (order: 2, 16384 bytes)            
[    0.007379] pinctrl core: initialized pinctrl subsystem                      
[    0.008361] NET: Registered protocol family 16                               
[    0.008834] DMA: preallocated 256 KiB pool for atomic coherent allocations   
[    0.009885] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint.
[    0.009982] hw-breakpoint: maximum watchpoint size is 8 bytes.               
[    0.021743] SCSI subsystem initialized                                       
[    0.021993] usbcore: registered new interface driver usbfs                   
[    0.022046] usbcore: registered new interface driver hub                     
[    0.022140] usbcore: registered new device driver usb                        
[    0.022382] pps_core: LinuxPPS API ver. 1 registered                         
[    0.022393] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom>
[    0.022415] PTP clock support registered                                     
[    0.022612] Advanced Linux Sound Architecture Driver Initialized.            
[    0.024319] clocksource: Switched to clocksource arch_sys_counter            
[    0.034142] NET: Registered protocol family 2                                
[    0.034814] TCP established hash table entries: 1024 (order: 0, 4096 bytes)  
[    0.034849] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)         
[    0.034872] TCP: Hash tables configured (established 1024 bind 1024)         
[    0.035007] UDP hash table entries: 256 (order: 1, 8192 bytes)               
[    0.035059] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)          
[    0.035282] NET: Registered protocol family 1                                
[    0.035967] RPC: Registered named UNIX socket transport module.              
[    0.035989] RPC: Registered udp transport module.                            
[    0.035995] RPC: Registered tcp transport module.                            
[    0.036001] RPC: Registered tcp NFSv4.1 backchannel transport module.        
[    0.037885] workingset: timestamp_bits=30 max_order=14 bucket_order=0        
[    0.043680] NFS: Registering the id_resolver key type                        
[    0.043740] Key type id_resolver registered                                  
[    0.043749] Key type id_legacy registered                                    
[    0.047928] Block layer SCSI generic (bsg) driver version 0.4 loaded (major )
[    0.047952] io scheduler noop registered                                     
[    0.047960] io scheduler deadline registered                                 
[    0.048260] io scheduler cfq registered (default)                            
[    0.048274] io scheduler mq-deadline registered                              
[    0.048282] io scheduler kyber registered                                    
[    0.048869] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO              
[    0.052104] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver  
[    0.052982] pwm-backlight backlight: backlight supply power not found, usingr
[    0.147212] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled         
[    0.150251] console [ttyS0] disabled                                         
[    0.170534] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 34, base_baud = 1A
[    0.749735] console [ttyS0] enabled                                          
[    0.756268] panel-simple panel: panel supply power not found, using dummy rer
[    0.765453] libphy: Fixed MDIO Bus: probed                                   
[    0.769921] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver       
[    0.776531] ehci-platform: EHCI generic platform driver                      
[    0.782032] ehci-platform 1c1a000.usb: EHCI Host Controller                  
[    0.787700] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus 1
[    0.795653] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000             
[    0.824364] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00            
[    0.831462] hub 1-0:1.0: USB hub found                                       
[    0.835402] hub 1-0:1.0: 1 port detected                                     
[    0.839938] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver           
[    0.846239] ohci-platform: OHCI generic platform driver                      
[    0.851805] ohci-platform 1c1a400.usb: Generic Platform OHCI controller      
[    0.858530] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus 2
[    0.866485] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400             
[    0.939323] hub 2-0:1.0: USB hub found                                       
[    0.943162] hub 2-0:1.0: 1 port detected                                     
[    0.950768] udc-core: couldn't find an available UDC - added [g_cdc] to lists
[    0.960467] sun6i-rtc 1c20400.rtc: rtc core: registered rtc-sun6i as rtc0    
[    0.967364] sun6i-rtc 1c20400.rtc: RTC enabled                               
[    0.971933] i2c /dev entries driver                                          
[    0.976832] input: ns2009_ts as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-000
[    0.985861] IR NEC protocol handler initialized                              
[    0.990400] IR RC5(x/sz) protocol handler initialized                        
[    0.995533] IR RC6 protocol handler initialized                              
[    1.000061] IR JVC protocol handler initialized                              
[    1.004610] IR Sony protocol handler initialized                             
[    1.009220] IR SANYO protocol handler initialized                            
[    1.013917] IR Sharp protocol handler initialized                            
[    1.018628] IR MCE Keyboard/mouse protocol handler initialized               
[    1.024464] IR XMP protocol handler initialized                              
[    1.029670] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, no)
[    1.094359] sunxi-mmc 1c0f000.mmc: base:0xc406b000 irq:24                    
[    1.101308] usbcore: registered new interface driver usbhid                  
[    1.106979] usbhid: USB HID core driver                                      
[    1.112789] NET: Registered protocol family 17                               
[    1.117475] Key type dns_resolver registered                                 
[    1.121869] Registering SWP/SWPB emulation handler                           
[    1.134778] simple-framebuffer 43e89000.framebuffer: framebuffer at 0x43e8900
[    1.145375] simple-framebuffer 43e89000.framebuffer: format=x8r8g8b8, mode=80
[    1.161569] Console: switching to colour frame buffer device 100x30          
[    1.174080] simple-framebuffer 43e89000.framebuffer: fb0: simplefb registere!
[    1.182839] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).      
[    1.189586] [drm] No driver support for vblank timestamp query.              
[    1.204990] sun4i-drm display-engine: bound 1100000.mixer (ops 0xc0743094)   
[    1.212352] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc0)
[    1.220086] fb: switching to sun4i-drm-fb from simple                        
[    1.225268] Console: switching to colour dummy device 80x30 

离线

#224 2019-05-17 16:18:32

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

Console: switching to colour dummy device 80x30

感觉应该是你的 u-boot bootargs 里面的 console 参数不是 /dev/ttyS0

导致默认控制台发生了切换.

离线

#225 2019-05-17 17:17:37

jianke512
会员
注册时间: 2019-05-17
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥,在Kernel的log中已确认console=ttyS0,与你在一楼推荐的CONFIG_BOOTARGS设置一样
另外Kernel version 4.14
困扰中

离线

#226 2019-05-17 17:20:57

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

jianke512 说:

晕哥,在Kernel的log中已确认console=ttyS0,与你在一楼推荐的CONFIG_BOOTARGS设置一样
另外Kernel version 4.14
困扰中

参考1: https://whycan.cn/t_2388.html (荔枝派zero/小智极客S3/V3s使用sunxi-fel 借 u-boot 启动 Linux系统, 无需 spi flash / TF 卡)


参考这个帖子, 一个一个替换文件, 逐步排除问题。

离线

#227 2019-05-19 16:31:06

lgliang
会员
注册时间: 2019-04-26
累计积分: 11

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥版主:“buildroot-2017.08.1” 自带的/usr/bin/ts_calibrate,测试时,提示“tslib: Selected device is not a touchscreen (must support ABS and KEY event types)”。 以前手动按装tslib. 设置:export TSLIB_TSDEVICE=/dev/input/event1
就可以找到touchscreen , “buildroot-2017.08.1” 自带的/usr/bin/ts_calibrate设置没有效果。

最近编辑记录 lgliang (2019-05-19 16:31:34)

离线

#228 2019-05-19 16:37:42

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

提示“tslib: Selected device is not a touchscreen (must support ABS and KEY event types)”。

是 TSLIB_TSDEVICE 环境变量没有测试

那现在可以了吗?

离线

#229 2019-05-19 16:49:34

lgliang
会员
注册时间: 2019-04-26
累计积分: 11

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

手动export TSLIB_TSDEVICE=/dev/input/event1 就可以了,我之前把这个命令写入/etc/profile里面没有效果,发现这个电阻触摸屏不是很准确。有时会跳动

最近编辑记录 lgliang (2019-05-19 17:04:13)

离线

#230 2019-05-19 17:09:28

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

lgliang 说:

手动export TSLIB_TSDEVICE=/dev/input/event1 就可以了,我之前把这个命令写入/etc/profile里面没有效果,发现这个电阻触摸屏不是很准确。有时会跳动

触摸不准是因为驱动没有防抖, 据说 tslib 的插件有防抖功能, 你研究一下.



驱动防抖 @john78 大神已经实现了: https://whycan.cn/t_1259.html#p14265

离线

#231 2019-05-19 17:11:19

lgliang
会员
注册时间: 2019-04-26
累计积分: 11

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

好的,谢谢晕哥

离线

#232 2019-05-20 14:01:19

jianke512
会员
注册时间: 2019-05-17
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:
jianke512 说:

晕哥,在Kernel的log中已确认console=ttyS0,与你在一楼推荐的CONFIG_BOOTARGS设置一样
另外Kernel version 4.14
困扰中

参考1: https://whycan.cn/t_2388.html (荔枝派zero/小智极客S3/V3s使用sunxi-fel 借 u-boot 启动 Linux系统, 无需 spi flash / TF 卡)


参考这个帖子, 一个一个替换文件, 逐步排除问题。

Hi,

   晕哥,此问题解决,参考以下链接的改法OK了,谢谢

https://www.lotlab.org/2018/07/28/record-of-using-licheepi-zero-part-1-u-boot-linux-buildroot/

离线

#233 2019-05-21 09:33:13

lgliang
会员
注册时间: 2019-04-26
累计积分: 11

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

请问晕哥,buildroot上的mPlayer是使用的软解码还是硬解码。

离线

#234 2019-05-21 09:36:35

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

lgliang 说:

请问晕哥,buildroot上的mPlayer是使用的软解码还是硬解码。

软解。


因为硬解码没有统一的标准。

离线

#235 2019-06-19 15:40:02

tobunto
会员
注册时间: 2019-03-04
累计积分: 9

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

我跟着教程都走通了,但是挂载emdebian系统后,启动时出错了,emdebian系统是根据https://licheezero.readthedocs.io/zh/latest/系统开发/emdebian.html制作的,错误是Starting init: /etc/init exists but couldn't execute it (error -13)
/bin/sh: 0: Can't open earlyprintk,没找到原因,有了解的能指点下吗。

离线

#236 2019-06-19 15:46:49

nuvoton
会员
注册时间: 2019-06-17
累计积分: 59

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

/etc/init exists but couldn't execute it (error -13)

/etc/init 存在, 但是不能执行, 看文件是不是没有执行属性, 或者依赖的库不存在,还是别的问题?

离线

#237 2019-06-20 09:13:32

tobunto
会员
注册时间: 2019-03-04
累计积分: 9

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

debian系统的/etc/init是个目录,/etc/init/下也都是一些配置文件,应该与执行权限没关

离线

#238 2019-06-20 09:20:08

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

tobunto 说:

debian系统的/etc/init是个目录,/etc/init/下也都是一些配置文件,应该与执行权限没关

那你的 bootargs 是什么? 系统第一个执行程序是 init=/etc/init ?

离线

#239 2019-06-20 09:35:47

tobunto
会员
注册时间: 2019-03-04
累计积分: 9

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

没指定第一个启动程序,是按帖子上面的配的:#define CONFIG_BOOTARGS      "console=ttyS0,115200 panic=5 rootwait root=/dev/mmcblk0p2 earlyprintk rw rootfstype=ext4 rootdelay=8 vt.global_cursor_default=0"

离线

#240 2019-07-04 00:14:25

xk100
会员
注册时间: 2018-12-13
累计积分: 41

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

jianke512 说:
晕哥 说:
jianke512 说:

晕哥,在Kernel的log中已确认console=ttyS0,与你在一楼推荐的CONFIG_BOOTARGS设置一样
另外Kernel version 4.14
困扰中

参考1: https://whycan.cn/t_2388.html (荔枝派zero/小智极客S3/V3s使用sunxi-fel 借 u-boot 启动 Linux系统, 无需 spi flash / TF 卡)


参考这个帖子, 一个一个替换文件, 逐步排除问题。

Hi,

   晕哥,此问题解决,参考以下链接的改法OK了,谢谢

https://www.lotlab.org/2018/07/28/record-of-using-licheepi-zero-part-1-u-boot-linux-buildroot/

碰到同样的问题。明天试试。

离线

#241 2019-07-05 21:47:30

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

买了一块licheepi zero ,准备在家试试 主线 uboot  +主线  kernel 。我发现kernel 的提交记录都是两年前的,是不是太老了。如果想玩是不是可以用最新的kernel 5.几版本好像。

离线

#242 2019-07-05 21:53:24

smartcar
会员
注册时间: 2018-02-19
累计积分: 681

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

4.13/4.14 还行, 用来量产了.

在线

#243 2019-07-24 17:18:36

太一酱鸭
会员
注册时间: 2019-07-03
累计积分: 154

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

root@wuyu-virtual-machine:/disk3/linuxzero/linux-master# make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- -j16 INSTALL_MOD_PATH=out modules
  CALL    scripts/atomic/check-atomics.sh
  CALL    scripts/checksyscalls.sh
  Building modules, stage 2.
  MODPOST 4591 modules
ERROR: "__sync_icache_dcache" [drivers/xen/xen-privcmd.ko] undefined!
scripts/Makefile.modpost:94: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1294: recipe for target 'modules' failed
make: *** [modules] Error 2


编译的时候出现这个问题,找了网上好多都没有找到答案

离线

#244 2019-07-24 17:32:09

太一酱鸭
会员
注册时间: 2019-07-03
累计积分: 154

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

太一酱鸭 说:

root@wuyu-virtual-machine:/disk3/linuxzero/linux-master# make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- -j16 INSTALL_MOD_PATH=out modules
  CALL    scripts/atomic/check-atomics.sh
  CALL    scripts/checksyscalls.sh
  Building modules, stage 2.
  MODPOST 4591 modules
ERROR: "__sync_icache_dcache" [drivers/xen/xen-privcmd.ko] undefined!
scripts/Makefile.modpost:94: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1294: recipe for target 'modules' failed
make: *** [modules] Error 2


编译的时候出现这个问题,找了网上好多都没有找到答案

貌似找到一个,明天上班再看看能不能解决

离线

#245 2019-08-05 10:33:34

太一酱鸭
会员
注册时间: 2019-07-03
累计积分: 154

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥我用linux3.4编译的zImage,然后一直点亮不了板子无法启动内核

 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
reading /boot.scr
284 bytes read in 14 ms (19.5 KiB/s)
## Executing script at 41900000
reading zImage
1866504 bytes read in 129 ms (13.8 MiB/s)
reading sun8i-v3s-blueberrypi-csi-ov2640.dtb
12240 bytes read in 26 ms (459 KiB/s)
## Flattened Device Tree blob at 41800000
   Booting using the fdt blob at 0x41800000
   Loading Device Tree to 42dfa000, end 42dfffcf ... OK
Cannot setup simplefb: node not found

Starting kernel ...

离线

#246 2019-08-05 10:39:58

太一酱鸭
会员
注册时间: 2019-07-03
累计积分: 154

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:
晕哥 说:

有没有 /dev/i2cX,   /dev/i2c/X 这些设备, 如果没有可能是 menuconfig 上面没有勾选 I2C User Interface


主要是这个错误

--- Opening /dev/video1...
[   33.650171] [VFE]vfe_open
Trying source module v4l2...[   33.656150] [VFE]..........................vfe clk open!.......................

[   33.667840] [VFE]vfe_open ok
[   33.671467] [VFE_ERR]input index(0) > dev->dev_qty(1)-1 invalid!, device_valid_flag[0] = 0
/dev/video1 opened.
No [   33.681675] [VFE]vfe_close
input was specified, using the f[   33.686958] [VFE]vfe select input flag = 0, s_input have not be used .
irst.
Unable to query [   33.697235] [VFE]..........................vfe clk close!.......................
input 0.
VIDIOC_ENUMIN[   33.708530] [VFE]vfe_close end
PUT: Invalid argument

不知道这个是什么造成的

我也是这个问题,请问您解决了吗

离线

#247 2019-08-05 11:31:36

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

我的解决了,你的是自己的板子,还是开发板?

离线

#248 2019-08-05 15:13:57

太一酱鸭
会员
注册时间: 2019-07-03
累计积分: 154

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:

我的解决了,你的是自己的板子,还是开发板?

我的是荔枝派zero,方便加qq(你猜)细聊吗

离线

#249 2019-08-05 16:48:26

太一酱鸭
会员
注册时间: 2019-07-03
累计积分: 154

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥小弟 说:

我的解决了,你的是自己的板子,还是开发板?

大佬方便加或者告诉我一下你的联系方式吗QAQ

离线

#250 2019-08-06 08:13:48

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

已经加了。不一定能解决,你的问题还是贴出来,晕哥都能解决的。我的很多很多的问题都是晕哥帮助解决的。

离线

#251 2019-08-15 16:40:54

a1326268019
会员
注册时间: 2019-08-15
累计积分: 12

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

各位大神,请问我编译uboot报这个错误怎么解决啊,u-boot是https://github.com/Lichee-Pi/u-boot下载的
里面确实没有LicheePi_Zero_defconfig
板子是荔枝派Zero V3s开发板

# make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- LicheePi_Zero_defconfig
***
*** Can't find default configuration "arch/../configs/LicheePi_Zero_defconfig"!
***
make[1]: *** [LicheePi_Zero_defconfig] Error 1
make: *** [LicheePi_Zero_defconfig] Error 2

最近编辑记录 a1326268019 (2019-08-15 16:46:09)

离线

#252 2019-08-15 17:32:32

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

用指定的分支, 比如 v3s-spi-experimental

离线

#253 2019-08-29 19:58:39

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

主线的kernel 是全志的官网弄出来的,还是索智弄出来的呢?还是licheepi zero的作者弄出来的呢?

离线

#254 2019-10-19 10:07:30

tianjianwudi
会员
注册时间: 2019-10-14
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

编译buildroot过程中下载文件太慢了,贼痛苦。
很不易的下载,在此分享下,拷贝到buildroot-2017.08/dl/ 下即可。

https://pan.baidu.com/s/1Pb18GiPxJedcUI-sYFqKQA&shfl=sharepset

离线

#255 2019-10-19 10:15:58

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

感谢楼上的朋友分享!

离线

#256 2019-10-19 15:38:40

tianjianwudi
会员
注册时间: 2019-10-14
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

请教晕哥及各位大神,为什么我将qt widgets中的例程编译后放 荔枝派zero 中运行时不显示文字。
一开始报未找到/lib/fonts文件夹,后来将buildroot-2017.08/output/target/usr/share/fonts拷贝到荔枝派中,未报任何信息,但还是不显示文字。

离线

#257 2019-10-19 16:05:10

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

勾选这个选项就可以显示了: BR2_PACKAGE_LIBERATION

离线

#258 2019-10-23 00:41:50

tianjianwudi
会员
注册时间: 2019-10-14
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

勾选这个选项就可以显示了: BR2_PACKAGE_LIBERATION

晕哥,请问 BR2_PACKAGE_LIBERATION 选项在哪啊?
我在buildroot 下 menuconfig 里找不到 BR2_PACKAGE_LIBERATION ,只在.config里找到以下内容。

#
# Fonts
#
BR2_PACKAGE_BITSTREAM_VERA=y
BR2_PACKAGE_CANTARELL=y
BR2_PACKAGE_DEJAVU=y
BR2_PACKAGE_DEJAVU_MONO=y
BR2_PACKAGE_DEJAVU_SANS=y
BR2_PACKAGE_DEJAVU_SERIF=y
BR2_PACKAGE_DEJAVU_SANS_CONDENSED=y
BR2_PACKAGE_DEJAVU_SERIF_CONDENSED=y
BR2_PACKAGE_FONT_AWESOME=y
BR2_PACKAGE_GHOSTSCRIPT_FONTS=y
BR2_PACKAGE_INCONSOLATA=y
BR2_PACKAGE_LIBERATION=y
BR2_PACKAGE_LIBERATION_MONO=y
BR2_PACKAGE_LIBERATION_SANS=y
BR2_PACKAGE_LIBERATION_SERIF=y

离线

#259 2019-10-23 09:19:49

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

Target packages  --->
    Fonts, cursors, icons, sounds and themes  --->
        [ ] Liberation (Free fonts)

离线

#260 2019-10-27 14:06:25

tianjianwudi
会员
注册时间: 2019-10-14
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

谢谢解答!
搞了好几天,还去重新移植qt5,结果还是只要将fonts下子目录中的字体文件移动到fonts目录下就能显示文字了。

离线

#261 2019-11-22 15:38:35

augyy
会员
注册时间: 2019-01-29
累计积分: 46

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

大家好!!請教各位大佬!! 本人用A33-Vstar開發板,想选通ov5640,但出現以下問題.
ov5640_1.png
ov5640_2.png

同sys_config.fex setting
ov5640_3.png

開啟
--- I2C support
[x] I2C device interface

离线

#262 2019-11-22 15:49:13

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

最前面 axp22_dldo3 创建 debugfs 出错了, 有没有影响?

离线

#263 2019-11-22 17:20:56

augyy
会员
注册时间: 2019-01-29
累计积分: 46

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

最前面 axp22_dldo3 创建 debugfs 出错了, 有没有影响?

改為以下. 但都出現問題
vip_dev0_iovdd = ""
vip_dev0_avdd = ""
vip_dev0_dvdd = ""

ov5640_4.png

离线

#264 2019-11-22 18:43:56

超级萌新
会员
注册时间: 2018-05-04
累计积分: 406

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

用逻辑分析仪抓 i2c 和 camera 的数据,看有什么情况

离线

#265 2019-11-25 17:25:41

augyy
会员
注册时间: 2019-01-29
累计积分: 46

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

超级萌新 说:

用逻辑分析仪抓 i2c 和 camera 的数据,看有什么情况

我發現 DOVDD-CSI 無 2.8V, AVDD-CSI 無 2.8V, DVDD18V-CSI 無1.8V, 是什麼原因?

离线

#266 2019-11-25 17:33:36

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

augyy 说:

我發現 DOVDD-CSI 無 2.8V, AVDD-CSI 無 2.8V, DVDD18V-CSI 無1.8V, 是什麼原因?

电源有问题

离线

#267 2019-11-25 18:11:08

augyy
会员
注册时间: 2019-01-29
累计积分: 46

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

电源有问题

是否關 axp22_dldo3 创建 debugfs 出错了問題?

离线

#268 2019-11-25 18:14:00

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

augyy 说:

是否關 axp22_dldo3 创建 debugfs 出错了問題?

不排除, 有可能的.

离线

#269 2019-11-26 13:45:59

augyy
会员
注册时间: 2019-01-29
累计积分: 46

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

不排除, 有可能的.

請問有冇解決方法!!因為找了很多網,都找不到解決方法

离线

#270 2019-11-26 14:11:16

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

另起一个帖子吧: https://whycan.cn/t_3297.html#p28559

离线

#271 2019-12-11 11:34:35

ma6254
会员
注册时间: 2019-11-03
累计积分: 35

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

我用win10的subsystem编译出现了这个错误,似乎是wsl内部IPC实现的问题
一会儿换用doker编译看看,可以的话我上传个编译用的docker镜像

fakeroot, while creating message channels: Function not implemented This may be due to a lack of SYSV IPC support. fakeroot: error while starting the `faked' daemon.

_20191211103600.png

离线

#272 2019-12-19 09:32:29

dml1048147924
会员
所在地: 江苏无锡
注册时间: 2019-11-08
累计积分: 92

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

哪位大神直到:
我的usb 插到荔枝派zero里,不工作。
USB 热插拔不起作用.pdf

离线

#273 2019-12-28 11:06:34

泽被苍生
会员
注册时间: 2019-12-15
累计积分: 24

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

git clone https://github.com/Lichee-Pi/linux.git -b zero-4.13.y  这条指令下载4.13y文件6个多G正常吗?

离线

#274 2019-12-28 11:13:38

raspberryman
会员
注册时间: 2019-12-27
累计积分: 78

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

我这里用 du -sh linux/ 命令显示 4 G 左右,

6G 可能是空间占用吧, 应该是正常的。

离线

#275 2019-12-28 11:19:09

泽被苍生
会员
注册时间: 2019-12-15
累计积分: 24

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

raspberryman 说:

我这里用 du -sh linux/ 命令显示 4 G 左右,

6G 可能是空间占用吧, 应该是正常的。

哦哦我以为有问题,这个还不能断点续传是吧。下载一点就中断了每次从头开始

离线

#276 2019-12-28 11:26:39

raspberryman
会员
注册时间: 2019-12-27
累计积分: 78

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

泽被苍生 说:

哦哦我以为有问题,这个还不能断点续传是吧。下载一点就中断了每次从头开始

墙内访问 github 是有这个问题, 最好是凌晨下载,速度飞快。

离线

#277 2019-12-28 12:15:25

泽被苍生
会员
注册时间: 2019-12-15
累计积分: 24

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

raspberryman 说:

墙内访问 github 是有这个问题, 最好是凌晨下载,速度飞快。

谢谢大佬的指点

离线

#278 2020-01-11 16:39:56

yuanlwjt
会员
注册时间: 2019-10-23
累计积分: 122

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

沉鱼 说:

这是我编译好的uboot, linux&dtb, rootfs: V3s_TFCard.7z
荔枝派Zero开发板网卡验证通过, 登陆账号root,无密码。
sha1sum文件校验码: 43c635802438e26c8fe96ada66255b664d52cddd

这里下载的文件按照步骤烧写到SD卡,V3S无法启动,出现 Starting init: /sbin/init exists but couldn't execute it (error -8)
Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance.
Rebooting in 5 seconds..
这种错误,什么原因呢?

离线

#279 2020-01-11 17:04:13

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

搜一下,这个问题问过很多次了。

离线

#280 2020-01-15 15:29:13

三哥
会员
注册时间: 2018-08-03
累计积分: 39

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

好长贴,翻死我了,下次继续来翻

离线

#281 2020-01-17 00:23:14

xql2008
会员
注册时间: 2019-12-26
累计积分: 5

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

你这个咋跟官方介绍的不一样呢?是因为官方的是最新的编译方式吗?我的板子是最新买的,按你的编译过程,烧进去,跑步起来,串口也没信息。如果,烧lichee_zero_test_Debian_LXDE,就可以跑起来,说明硬件没问题。可能是编译哪里不对。晕哥,能帮我分析下吗?

离线

#282 2020-01-19 17:16:57

晕哥小弟
会员
注册时间: 2019-04-04
累计积分: 294

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

请教下,这是为什么?

17648] platform reg-20-cs-dcdc2: Driver reg-20-cs-dcdc2 requests probe deferral
[    1.826401] *******************sd init ok*******************
[    1.832989] platform reg-20-cs-dcdc3: Driver reg-20-cs-dcdc3 requests probe deferral
[    1.841895] platform reg-20-cs-ldo1: Driver reg-20-cs-ldo1 requests probe deferral
[    1.851727] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[    1.860402] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[    1.869054] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[    1.877799] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[    1.896177] *******************Try sdio*******************
[    1.905705] *******************Try sd *******************
[    1.915233] *******************Try mmc*******************
[    1.967081] *******************Try sdio*******************
[    1.977772] *******************Try sd *******************
[    1.985450] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.996146] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    2.005425] *******************Try mmc*******************
[    2.012949] EXT4-fs (mmcblk0p2): couldn't mount RDWR because of unsupported optional features (400)
[    2.033832] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(179,2)
[    2.043468] Backtrace: 
[    2.046441] [<c00133a4>] (dump_backtrace+0x0/0x104) from [<c03a7b7c>] (dump_stack+0x18/0x1c)
[    2.056035]  r6:c05e24f0 r5:c303b024 r4:c303b024 r3:00000001
[    2.062918] [<c03a7b64>] (dump_stack+0x0/0x1c) from [<c03a7f4c>] (panic+0x78/0x1bc)
[    2.071651] [<c03a7ed4>] (panic+0x0/0x1bc) from [<c0531d5c>] (mount_block_root+0x248/0x280)
[    2.081144]  r3:c3023efc r2:c04c4e7a r1:c3023f30 r0:c04aae7e
[    2.088007]  r7:c04aaee2
[    2.091061] [<c0531b14>] (mount_block_root+0x0/0x280) from [<c0531dec>] (mount_root+0x58/0x6c)
[    2.100850] [<c0531d94>] (mount_root+0x0/0x6c) from [<c0531f30>] (prepare_namespace+0x130/0x190)
[    2.110826]  r5:c055015d r4:c05e1364
[    2.115149] [<c0531e00>] (prepare_namespace+0x0/0x190) from [<c053197c>] (kernel_init+0x174/0x1b4)
[    2.125317]  r5:c0550120 r4:00000007
[    2.129643] [<c0531808>] (kernel_init+0x0/0x1b4) from [<c0031fd4>] (do_exit+0x0/0x638)
[    2.138654]  r9:00000000 r8:00000000 r7:00000013 r6:c0031fd4 r5:c0531808
[    2.146596] r4:00000000
[    2.149851] Rebooting in 5 seconds..
[    7.154200] Restarting Linux version 3.4.39 (he@he) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-29) ) #55 Thu Dec 12 16:12:04 CST 2019
[    7.154212] 

离线

#283 2020-01-19 17:54:14

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

根文件系统 mount 失败.

离线

#284 2020-01-20 21:42:59

joyhope
会员
注册时间: 2020-01-16
累计积分: 38

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

#282 楼的错误我也遇到多次,在主线上没有遇到,在3.4 上遇到。 我不知道哪里下载的3.4 和 这个论坛里面一个3.4 的版本有差异。我用论坛3.4的配置,结果Menuconfig  一堆的问题。后来重新下载论坛的3.4,按照指南操作就没有遇到#282的问题。

离线

#285 2020-02-25 17:25:29

yytyu
会员
注册时间: 2018-11-01
累计积分: 28

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

mark

离线

#286 2020-03-09 08:11:45

mcu1234mcu
会员
注册时间: 2020-02-22
累计积分: 18

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

QQ图片20200309080732.jpg
编译uboot出现上面的错误,在下小白,刚入手荔枝派ZERO,请教晕哥

离线

#287 2020-03-09 08:31:23

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

sudo apt-get install device-tree-compiler

提示缺啥装啥就行

@mcu1234mcu

离线

#288 2020-03-11 09:11:08

mcu1234mcu
会员
注册时间: 2020-02-22
累计积分: 18

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

sudo apt-get install device-tree-compiler

提示缺啥装啥就行

@mcu1234mcu

搞定了,谢谢

离线

#289 2020-03-15 09:19:47

yuanlwjt
会员
注册时间: 2019-10-23
累计积分: 122

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

按照论坛里的教程:
    1) 删除TF卡所有分区
    2) 将uboot写入到sd卡8k偏移处(必须8K偏移, brom龟腚的)。
        sudo dd if=u-boot-sunxi-with-spl.bin of=/dev/sdX bs=1024 seek=8
    3) 建立第一个分区,大小32M(可以随意填写), 格式FAT16, 把zImage, sun8i-v3s-licheepi-zero-dock.dtb拷贝到 这个分区
    4) 建立第二个分区,用尽剩余空间,格式ext4, 把buildroot产生的rootfs.tar解压到该分区根目录
        tar xvf output/images/rootfs.tar -C /挂载的tf卡第二个分区目录

在V3S ZERO开发板上运行后,出现如下情况:

[    1.391582] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.401860] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.552817] EXT4-fs (mmcblk0p2): warning: mounting fs with errors, running e2fsck is recommended
[    1.567509] EXT4-fs (mmcblk0p2): recovery complete
[    1.577550] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.585719] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    1.594166] devtmpfs: mounted
[    1.598397] Freeing unused kernel memory: 1024K
[    1.613776] Starting init: /sbin/init exists but couldn't execute it (error -5)
[    1.623757] Starting init: /bin/sh exists but couldn't execute it (error -5)
[    1.630930] Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance.
[    1.645087] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.13.16-licheepi-zero #1
[    1.652298] Hardware name: Allwinner sun8i Family
[    1.657036] [<c010e514>] (unwind_backtrace) from [<c010b1b8>] (show_stack+0x10/0x14)
[    1.664779] [<c010b1b8>] (show_stack) from [<c065e5a4>] (dump_stack+0x88/0x9c)
[    1.672001] [<c065e5a4>] (dump_stack) from [<c011b48c>] (panic+0xdc/0x248)
[    1.678875] [<c011b48c>] (panic) from [<c06700ec>] (kernel_init+0x100/0x110)
[    1.685919] [<c06700ec>] (kernel_init) from [<c0107538>] (ret_from_fork+0x14/0x3c)
[    1.693492] Rebooting in 5 seconds..

板子启动不了?是什么情况?

如果把第二步改一下:
  4) 建立第二个分区,大小100M,格式ext4, 把buildroot产生的rootfs.tar解压到该分区根目录
        tar xvf output/images/rootfs.tar -C /挂载的tf卡第二个分区目录
第二个分区改成100M,就可以正常启动。200M就不行了,是什么问题呢?


遇到同样问题,该如何解决?

离线

#290 2020-03-15 09:29:45

异乡是故乡
会员
注册时间: 2019-11-15
累计积分: 71

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

你的根文件系统出问题了, 换张卡试一试.

离线

#291 2020-03-15 10:46:55

yuanlwjt
会员
注册时间: 2019-10-23
累计积分: 122

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

异乡是故乡 说:

你的根文件系统出问题了, 换张卡试一试.

好的,我换张卡试试看

离线

#292 2020-03-21 14:29:40

yuanlwjt
会员
注册时间: 2019-10-23
累计积分: 122

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

换了张SD可以了,但是按照
1) 删除TF卡所有分区
    2) 将uboot写入到sd卡8k偏移处(必须8K偏移, brom龟腚的)。
        sudo dd if=u-boot-sunxi-with-spl.bin of=/dev/sdb bs=1024 seek=8
    3) 建立第一个分区,大小32M(可以随意填写), 格式FAT16, 把zImage, sun8i-v3s-licheepi-zero-dock.dtb拷贝到 这个分区
    4) 建立第二个分区,用尽剩余空间,格式ext4, 把buildroot产生的rootfs.tar解压到该分区根目录
        sudo tar xvf output/images/rootfs.tar -C /media/bao/rootfs
这样子烧写到SD卡
偶尔几次就又启动不了,偶尔几次又可以

离线

#293 2020-03-21 14:31:15

smartcar
会员
注册时间: 2018-02-19
累计积分: 681

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

你把rootfs文件系统写坏了吗?  或者再换一张卡试一试。

在线

#294 2020-03-30 19:36:49

jengy
会员
注册时间: 2020-03-30
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

各位老大,我刷了V3s_TFCard.7z,我是一体的板子,用了_dock 设备树,可是网卡还是没看到,是什么情况呀?
是dts文件还要做修改吗?请不吝赐教。

log:

U-Boot SPL 2017.01-rc2-00075-gec3f3ba-dirty (Dec 15 2017 - 14:00:51)
DRAM: 64 MiB
Trying to boot from MMC1

U-Boot 2017.01-rc2-00075-gec3f3ba-dirty (Dec 15 2017 - 14:00:51 +0800) Allwinner Technology

CPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
MMC:   SUNXI SD/MMC: 0
SF: unrecognized JEDEC id bytes: 00, 00, 00
*** Warning - spi_flash_probe() failed, using default environment

Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In:    serial@01c28000
Out:   serial@01c28000
Err:   serial@01c28000


U-Boot 2017.01-rc2-00075-gec3f3ba-dirty (Dec 15 2017 - 14:00:51 +0800) Allwinner Technology

CPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
MMC:   SUNXI SD/MMC: 0
SF: unrecognized JEDEC id bytes: 00, 00, 00
*** Warning - spi_flash_probe() failed, using default environment

Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In:    serial@01c28000
Out:   serial@01c28000
Err:   serial@01c28000
Net:   phy interface0
eth0: ethernet@1c30000
starting USB...
No controllers found
Hit any key to stop autoboot:  0
reading zImage
4016104 bytes read in 634 ms (6 MiB/s)
reading sun8i-v3s-licheepi-zero-dock.dtb
11803 bytes read in 27 ms (426.8 KiB/s)
## Flattened Device Tree blob at 41800000
   Booting using the fdt blob at 0x41800000
   Loading Device Tree to 42dfa000, end 42dffe1a ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.13.0-licheepi-zero+ (hexing@ubuntu) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1)) #46 SMP Fri Dec 15 14:36:43 CST 2017
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Lichee Pi Zero with Dock
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] percpu: Embedded 16 pages/cpu @c3de6000 s33920 r8192 d23424 u65536
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15883
[    0.000000] Kernel command line: console=ttyS0,115200 panic=5 mtdparts=spi32766.0:1M(uboot),64k(dtb),4M(kernel),-(rootfs) rootwait root=/dev/mmcblk0p2 earlyprintk rw  vt.global_cursor_default=0
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 53572K/64036K available (6144K kernel code, 222K rwdata, 1480K rodata, 1024K init, 266K bss, 10464K reserved, 0K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc4000000 - 0xff800000   ( 952 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc3e89000   (  62 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0700000   (7136 kB)
[    0.000000]       .init : 0xc0900000 - 0xc0a00000   (1024 kB)
[    0.000000]       .data : 0xc0a00000 - 0xc0a37b00   ( 223 kB)
[    0.000000]        .bss : 0xc0a3ebec - 0xc0a8153c   ( 267 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU event tracing is enabled.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000019] Switching to timer-based delay loop, resolution 41ns
[    0.000193] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000426] Console: colour dummy device 80x30
[    0.000464] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000480] pid_max: default: 32768 minimum: 301
[    0.000610] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000624] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.001225] CPU: Testing write buffer coherency: ok
[    0.001606] /cpus/cpu@0 missing clock-frequency property
[    0.001630] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.002066] Setting up static identity map for 0x40100000 - 0x40100060
[    0.002239] Hierarchical SRCU implementation.
[    0.002732] smp: Bringing up secondary CPUs ...
[    0.002747] smp: Brought up 1 node, 1 CPU
[    0.002757] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.002764] CPU: All CPU(s) started in SVC mode.
[    0.003531] devtmpfs: initialized
[    0.006677] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.006973] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.006999] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.007167] pinctrl core: initialized pinctrl subsystem
[    0.008048] random: get_random_u32 called from bucket_table_alloc+0xf0/0x250 with crng_init=0
[    0.008190] NET: Registered protocol family 16
[    0.008677] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.009802] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.009819] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.023331] SCSI subsystem initialized
[    0.023635] usbcore: registered new interface driver usbfs
[    0.023704] usbcore: registered new interface driver hub
[    0.023803] usbcore: registered new device driver usb
[    0.024055] pps_core: LinuxPPS API ver. 1 registered
[    0.024068] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.024093] PTP clock support registered
[    0.024322] Advanced Linux Sound Architecture Driver Initialized.
[    0.026178] clocksource: Switched to clocksource arch_sys_counter
[    0.036999] NET: Registered protocol family 2
[    0.037589] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.037623] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.037647] TCP: Hash tables configured (established 1024 bind 1024)
[    0.037772] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.037820] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.038043] NET: Registered protocol family 1
[    0.038633] RPC: Registered named UNIX socket transport module.
[    0.038653] RPC: Registered udp transport module.
[    0.038659] RPC: Registered tcp transport module.
[    0.038664] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.040625] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.049604] NFS: Registering the id_resolver key type
[    0.049659] Key type id_resolver registered
[    0.049666] Key type id_legacy registered
[    0.049715] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.051190] random: fast init done
[    0.053994] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    0.054019] io scheduler noop registered
[    0.054028] io scheduler deadline registered
[    0.054276] io scheduler cfq registered (default)
[    0.054290] io scheduler mq-deadline registered
[    0.054298] io scheduler kyber registered
[    0.058664] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.127674] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.130946] console [ttyS0] disabled
[    0.151221] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 36, base_baud = 1500000) is a U6_16550A
[    0.741916] console [ttyS0] enabled
[    0.750108] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 00, 00
[    0.756757] m25p80: probe of spi32766.0 failed with error -2
[    0.762967] libphy: Fixed MDIO Bus: probed
[    0.767734] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[    0.773529] dwmac-sun8i 1c30000.ethernet: No regulator found
[    0.779313] dwmac-sun8i 1c30000.ethernet: Will use internal PHY
[    0.785307] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 148000 (expect 38000)
[    0.794892] dwmac-sun8i 1c30000.ethernet: Chain mode enabled
[    0.800586] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported
[    0.807816] dwmac-sun8i 1c30000.ethernet: Normal descriptors
[    0.813469] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported
[    0.820693] dwmac-sun8i 1c30000.ethernet: COE Type 2
[    0.825653] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported
[    0.832628] libphy: stmmac: probed
[    0.837960] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.844499] ehci-platform: EHCI generic platform driver
[    0.850145] ehci-platform 1c1a000.usb: EHCI Host Controller
[    0.855767] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[    0.863738] ehci-platform 1c1a000.usb: irq 26, io mem 0x01c1a000
[    0.896194] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[    0.903449] hub 1-0:1.0: USB hub found
[    0.907395] hub 1-0:1.0: 1 port detected
[    0.911889] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.918189] ohci-platform: OHCI generic platform driver
[    0.923762] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[    0.930493] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[    0.938454] ohci-platform 1c1a400.usb: irq 27, io mem 0x01c1a400
[    1.011305] hub 2-0:1.0: USB hub found
[    1.015145] hub 2-0:1.0: 1 port detected
[    1.022794] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[    1.032379] input: 1c22800.lradc as /devices/platform/soc/1c22800.lradc/input/input0
[    1.041390] sun6i-rtc 1c20400.rtc: rtc core: registered rtc-sun6i as rtc0
[    1.048300] sun6i-rtc 1c20400.rtc: RTC enabled
[    1.052851] i2c /dev entries driver
[    1.057877] input: ns2009_ts as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0048/input/input1
[    1.067389] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.136223] sunxi-mmc 1c0f000.mmc: base:0xc407b000 irq:23
[    1.196204] sunxi-mmc 1c10000.mmc: base:0xc423b000 irq:24
[    1.202595] usbcore: registered new interface driver usbhid
[    1.208266] usbhid: USB HID core driver
[    1.214142] sun4i-codec 1c22c00.codec: ASoC: /soc/codec-analog@01c23000 not registered
[    1.222206] sun4i-codec 1c22c00.codec: Failed to register our card
[    1.230865] NET: Registered protocol family 17
[    1.235451] Key type dns_resolver registered
[    1.239988] Registering SWP/SWPB emulation handler
[    1.251716] simple-framebuffer 43e89000.framebuffer: framebuffer at 0x43e89000, 0x177000 bytes, mapped to 0xc4400000
[    1.262392] simple-framebuffer 43e89000.framebuffer: format=x8r8g8b8, mode=800x480x32, linelength=3200
[    1.278762] Console: switching to colour frame buffer device 100x30
[    1.291196] simple-framebuffer 43e89000.framebuffer: fb0: simplefb registered!
[    1.299828] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[    1.311262] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[    1.317113] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[    1.325057] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.334326] hub 3-0:1.0: USB hub found
[    1.338495] mmc0: new high speed SDHC card at address b368
[    1.344629] hub 3-0:1.0: 1 port detected
[    1.348840] mmcblk0: mmc0:b368 CBADS 30.0 GiB
[    1.355532] using random self ethernet address
[    1.360101] using random host ethernet address
[    1.364963]  mmcblk0: p1 p2
[    1.369819] usb0: HOST MAC 02:51:3b:c0:fe:f4
[    1.374141] usb0: MAC c2:86:96:e9:19:df
[    1.378164] g_cdc gadget: CDC Composite Gadget, version: King Kamehameha Day 2008
[    1.385642] g_cdc gadget: g_cdc ready
[    1.392015] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[    1.400718] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01 00:17:46 UTC (1066)
[    1.409260] vcc5v0: disabling
[    1.412238] ALSA device list:
[    1.415201]   #0: V3s Audio Codec
[    1.420572] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.429785] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.440045] mmc1: new high speed SDIO card at address 0001
[    1.555346] EXT4-fs (mmcblk0p2): recovery complete
[    1.562454] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.570666] VFS: Mounted root (ext4 filesystem) on device 179:2.
[    1.578269] devtmpfs: mounted
[    1.582532] Freeing unused kernel memory: 1024K
[    1.685800] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
Starting logging: OK
Initializing random number generator... done.
Starting network: OK

Welcome to Buildroot
buildroot login:

最近编辑记录 jengy (2020-03-30 19:42:02)

离线

#295 2020-03-31 09:19:00

jengy
会员
注册时间: 2020-03-30
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

以太网功能正常!设备树和驱动都已经开启以太网了。

@晕哥 我用了你发的 V3s_TFCard,为什么我的网卡在登录后用 ifconfig 命令没看到。

u-boot启动日志如下:

U-Boot 2017.01-rc2-00075-gec3f3ba-dirty (Dec 15 2017 - 14:00:51 +0800) Allwinner Technology

CPU:   Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM:  64 MiB
MMC:   SUNXI SD/MMC: 0
SF: unrecognized JEDEC id bytes: 00, 00, 00
*** Warning - spi_flash_probe() failed, using default environment

Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In:    serial@01c28000
Out:   serial@01c28000
Err:   serial@01c28000
Net:   phy interface0
eth0: ethernet@1c30000
starting USB...
No controllers found
Hit any key to stop autoboot:  0
reading zImage
4016104 bytes read in 634 ms (6 MiB/s)
reading sun8i-v3s-licheepi-zero-dock.dtb
11803 bytes read in 27 ms (426.8 KiB/s)
## Flattened Device Tree blob at 41800000
   Booting using the fdt blob at 0x41800000
   Loading Device Tree to 42dfa000, end 42dffe1a ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.13.0-licheepi-zero+ (hexing@ubuntu) (gcc version 4.8.4 (Ubuntu/Linaro 4.8.4-2ubuntu1~14.04.1)) #46 SMP Fri Dec 15 14:36:43 CST 2017
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Lichee Pi Zero with Dock

离线

#296 2020-03-31 09:22:33

晕哥
管理员
注册时间: 2017-09-06
累计积分: 9,190

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

ifconfig -a

离线

#297 2020-03-31 12:33:06

jengy
会员
注册时间: 2020-03-30
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

嗯,找到网卡了,谢谢!

离线

#298 2020-04-13 08:38:19

zhang235hai
会员
注册时间: 2020-04-06
累计积分: 106

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

Starting logging: OK
Initializing random number generator... done.
Starting network: OK
# ls
analogclock  lib          media        root         tmp
bin          lib32        mnt          run          usr
dev          linuxrc      opt          sbin         var
etc          lost+found   proc         sys
# ./analogclock -platform linuxfb
-/bin/sh: ./analogclock: Permission denied
# 

在运行QT文件的时候报错 Permission denied
请问是什么原因呢?

离线

#299 2020-04-13 08:45:47

X3
会员
注册时间: 2020-04-08
累计积分: 18

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

没有执行属性吧, 试一试 chmod +x analogclock

离线

#300 2020-04-13 09:15:15

zhang235hai
会员
注册时间: 2020-04-06
累计积分: 106

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

X3 说:

没有执行属性吧, 试一试 chmod +x analogclock


谢谢,按照你的方式已经可以了!

离线

#301 2020-04-22 15:46:24

whoam1
会员
注册时间: 2020-04-09
累计积分: 18

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

多谢分享、大佬,请问怎么启动有线网络?

离线

#302 2020-05-07 10:00:58

yyb390931229
会员
注册时间: 2020-04-27
累计积分: 7

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

搞了半天没起来,学习中感谢楼主

离线

#303 2020-05-08 08:58:53

mysteryli
会员
注册时间: 2020-03-05
累计积分: 143
个人网站

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

为啥推荐vm,我用的virtual,请问这里面是有什么坑么

离线

#304 2020-05-08 09:07:57

哇酷小二
管理员
注册时间: 2020-04-22
累计积分: 1,807

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

mysteryli 说:

为啥推荐vm,我用的virtual,请问这里面是有什么坑么

virtual pc容易挂,换过几台电脑都一样,后来换VMWARE一直到今,很稳定。

在线

#305 2020-05-08 15:23:17

zyj
会员
注册时间: 2020-05-08
累计积分: 5

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

系统刷完后大部分时间无法启动,其少数断电后可以起来,但是系统起来后有时出现系统加载中途死机或无限重启的情况,有时启动后几分钟系统出现死机的情况

离线

#306 2020-05-09 12:21:40

JQH
会员
注册时间: 2020-05-09
累计积分: 1

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

是的,都没理解这句话,谢谢各位

离线

#307 2020-05-10 12:12:40

grantho
会员
注册时间: 2020-03-21
累计积分: 40

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

请问串口控制台是ttyS0,而与SDC0引脚是复用的,从TF卡启动,控制台与TF卡都同时工作正常吗?

离线

#308 2020-05-10 12:14:04

有梦的地方
会员
注册时间: 2020-03-17
累计积分: 284

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

grantho 说:

请问串口控制台是ttyS0,而与SDC0引脚是复用的,从TF卡启动,控制台与TF卡都同时工作正常吗?

只能二选一。

离线

#309 2020-05-10 12:18:53

grantho
会员
注册时间: 2020-03-21
累计积分: 40

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

有梦的地方 说:

只能二选一。

那为什么看到评论中的打印,控制台工作正常,TF卡文件系统分区挂载也正常呢?不大明白

最近编辑记录 grantho (2020-05-10 12:19:25)

离线

#310 2020-05-10 12:45:36

哇酷小二
管理员
注册时间: 2020-04-22
累计积分: 1,807

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

grantho 说:

那为什么看到评论中的打印,控制台工作正常,TF卡文件系统分区挂载也正常呢?不大明白

是另外一组串口0,详情参考荔枝派zero原理图。

在线

#311 2020-05-11 16:14:08

lhb882
会员
注册时间: 2020-03-27
累计积分: 10

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

请问有没有32M得sunxi工具

离线

#312 2020-05-11 16:19:04

哇酷小二
管理员
注册时间: 2020-04-22
累计积分: 1,807

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

lhb882 说:

请问有没有32M得sunxi工具

https://whycan.cn/t_444.html

在线

#313 2020-05-21 21:13:09

yvan
会员
注册时间: 2019-10-16
累计积分: 5

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

膜拜大佬! 请问一下要如何支持双屏异显示啊?

离线

#314 2020-05-28 09:59:43

andrewchen175
会员
注册时间: 2020-04-26
累计积分: 22

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

请教各位大咖,按步骤进行烧录之后,插卡启动,屏幕只出现一张LOGO图,然后图没了,屏幕亮但没内容,LED 在闪,这样是正常的吗?如果不正常,会是哪里出问题,在线等,多谢了

离线

#315 2020-05-28 10:16:48

哇酷小二
管理员
注册时间: 2020-04-22
累计积分: 1,807

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

正常,接串口终端操作吧。

在线

#316 2020-05-31 14:31:01

TDA2030
会员
注册时间: 2019-10-17
累计积分: 7

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

编译老是失败,好想下载楼主打包好的镜像,给我个机会

离线

#317 2020-05-31 14:37:26

TDA2030
会员
注册时间: 2019-10-17
累计积分: 7

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

编译u-boot 报错:arch/arm/dts/sun8i-v3s-licheepi-zero.dtb: Warning (simple_bus_reg): Node /soc/interrupt-controller@01c81000 simple-bus unit address format error, expected "1c81000"
重新clone后也是一个样,求救大神

离线

#318 2020-06-07 08:57:56

andrewchen175
会员
注册时间: 2020-04-26
累计积分: 22

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

社区主任好,版主好,楼主好,这个启动系统已经建立,同时学到了一些linux的入门操作,谢谢楼主。接下来应该怎么写用户程序?怎么把用户程序加入系统中运行?有没有类似“helloword!"之类的例程详细介绍?翻了半天没发现有相关主题,求相关资源,入门小白也能看懂的。

离线

#319 2020-06-07 09:11:44

哇酷小二
管理员
注册时间: 2020-04-22
累计积分: 1,807

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

andrewchen175 说:

社区主任好,版主好,楼主好,这个启动系统已经建立,同时学到了一些linux的入门操作,谢谢楼主。接下来应该怎么写用户程序?怎么把用户程序加入系统中运行?有没有类似“helloword!"之类的例程详细介绍?翻了半天没发现有相关主题,求相关资源,入门小白也能看懂的。

写一个简单的 HelloWorld app程序, 用gcc编译,

比如路径是 /opt/helloworld

你创建 /etc/profile.d/app 文件

添加一行: /opt/helloworld

就能开机执行了.

在线

#320 2020-06-17 21:25:09

forcaowu
会员
注册时间: 2020-06-17
累计积分: 0

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

感觉这个站还比较靠谱些,其他地方找资料好少

离线

#321 2020-06-18 16:47:20

panchuane
会员
注册时间: 2020-06-18
累计积分: 2

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

刚买了这个板子,学习一下你的经验。很有用,谢谢了。

离线

#322 2020-06-29 16:13:44

liuy
会员
注册时间: 2020-06-24
累计积分: 7

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

这个F1C100S能不能用SD卡烧录SPI  NAND啊

离线

#323 2020-07-03 16:35:04

JiuHuan
会员
注册时间: 2020-06-28
累计积分: 4

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

对于buildroot,翻了又翻。 一直不能理解,到底需要勾选哪些(除了 cpu 和 工具链 必配置之外的)。 百度找的相关资料也描述的不多。这块 有没有好的资料推荐。

离线

#324 2020-07-08 14:09:17

174high
会员
注册时间: 2020-07-08
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

不能执行 /sbin/init 。 启动的时候,请问是什么情况。

离线

#325 2020-07-08 15:32:21

174high
会员
注册时间: 2020-07-08
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

晕哥 说:

是不是已经被勾选了, 看下 output/target/usr/bin 目录, 有没有 ts_xxxx 文件.

buildroot 版本多少合适呢?

离线

#326 2020-07-12 21:34:21

v3s_tester
会员
注册时间: 2020-07-12
累计积分: 1

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

第一次接触V3S,想自己编译uboot,内核和文件系统,然后烧到TF卡中。这篇文章正好是需要的,学习了!

离线

#327 2020-07-17 12:30:03

selected
会员
注册时间: 2020-04-10
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

刚入门这个荔枝派zero,把linux源码、设备树编译好了,那个跟文件系统是真的难受。。。求讲解视频

离线

#328 2020-07-17 12:50:23

selected
会员
注册时间: 2020-04-10
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

根文件系统编译需要从网络上下载其他资源吗??进度条一直卡着,等待很久才跳出去,死活下载不了。哎。

离线

#329 2020-07-18 07:35:57

selected
会员
注册时间: 2020-04-10
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

根文件系统的版本:buildroot-2017.08.1.tar.gz  ubantu用的是16的版本 ,编译的时候下载很多资源 例如uclibc 等等,进度条不走,可以把获取源文件的网址换成一个网速快的嘛?

离线

#330 2020-07-18 08:17:28

哇酷小二
管理员
注册时间: 2020-04-22
累计积分: 1,807

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

selected 说:

根文件系统的版本:buildroot-2017.08.1.tar.gz  ubantu用的是16的版本 ,编译的时候下载很多资源 例如uclibc 等等,进度条不走,可以把获取源文件的网址换成一个网速快的嘛?

建议在vultr的日本vps上面编译, 没有进度条问题,可以按时长租用,销毁实例停止收费:

https://whycan.cn/t_3759.html
https://whycan.cn/t_3884.html

其他的不方便多说。

在线

#331 2020-08-05 21:03:50

白菜爱西瓜
会员
注册时间: 2020-08-05
累计积分: 8

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

这里的内容下载下来试试看,希望可以解决啊

离线

#332 2020-08-07 16:05:23

haxxjj77
会员
注册时间: 2020-08-07
累计积分: 1

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

写的很详细真好,新手都能照搬操作下来,什么时候能出一个烧写SPIFLASH的教程就好了,期待!

离线

#333 2020-08-08 09:52:59

hilam8899
会员
注册时间: 2020-08-08
累计积分: 10

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

好资料,这里的内容下载下来试试看,谢谢!

离线

#334 2020-08-10 19:18:59

popmark
会员
注册时间: 2020-04-15
累计积分: 2

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

刚刚入手zero dock,好好读了一下,受益匪浅

离线

#335 2020-08-11 00:35:03

yongzong
会员
注册时间: 2020-08-11
累计积分: 3

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

这里的内容下载下来试试看,希望可以解决啊

离线

#336 2020-08-12 09:38:19

jkl
会员
注册时间: 2019-11-18
累计积分: 112

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

沉鱼 说:

但是lcd上出现了用户登陆提示,这种情况你把 uboot,设备树, Linux都用我上面写的。
log跑屏幕上去这个是在哪里配置的,我现在还没找到,如果你找到麻烦跟帖一下。

你好,请问log跑到屏幕上这个问题您解决了吗?

离线

#337 2020-09-10 20:24:41

andrewchen175
会员
注册时间: 2020-04-26
累计积分: 22

Re: 荔枝派Zero V3s开发板入坑记录 (TF/SD卡启动)(主线Linux,主线u-boot)

想把Vrtc 和其它3.3V分开,找不到J12和R6,求荔枝派Zero V3s开发板的PCB丝印图,多谢先!

离线

页脚

工信部备案:粤ICP备20025096号 Powered by FluxBB